Yard Tool Rack Builder
Shopping list
Pick a 2×6 with no knots along the front edge; the slots cut right through it and a knot there pops out. The ledger just needs to be straight.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×6×8′ SPF board | 1 | $6.48 | $6.48 |
| 2×4×8′ SPF board | 1 | $3.50 | $3.50 |
| #9 × 3″ construction screws, 1-lb box (about 21) | 1 | $10.00 | $10.00 |
| ¼″ × 4″ structural wood screw (ledger into studs) | 10 | $1.10 | $11.00 |
| Vinyl-coated screw-in utility hook (hose, cords, trimmer) | 4 | $3.50 | $14.00 |
| Exterior paint or poly, 1 qt | 1 | $15.00 | $15.00 |
| Total | $59.98 |
Tools: drill with a 1¾″ Forstner or spade bit, jigsaw or handsaw, circular or miter saw, drill/driver, tape, square, level, stud finder (wall).
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
1 board56% yield2×4 × 8′
1 board82% yieldHandles drop into U-shaped slots cut in the front edge of a flat 2×6 and stand on the floor below it. Most long-handled tools have 1⅛″–1⅜″ handles; the slots are 1¾″ so a gloved hand can drop one in without aiming.
- 1
Shopping list
Pick a 2×6 with no knots along the front edge; the slots cut right through it and a knot there pops out. The ledger just needs to be straight.
Item Qty Each Total 2×6×8′ SPF board 1 $6.48 $6.48 2×4×8′ SPF board 1 $3.50 $3.50 #9 × 3″ construction screws, 1-lb box (about 21) 1 $10.00 $10.00 ¼″ × 4″ structural wood screw (ledger into studs) 10 $1.10 $11.00 Vinyl-coated screw-in utility hook (hose, cords, trimmer) 4 $3.50 $14.00 Exterior paint or poly, 1 qt 1 $15.00 $15.00 Total $59.98 Tools: drill with a 1¾″ Forstner or spade bit, jigsaw or handsaw, circular or miter saw, drill/driver, tape, square, level, stud finder (wall).
- 2
Cut list
Cut the rail to length first, then lay out the slots on it before cutting anything else; it's the one part you can ruin.
Tag Part Length Qty Cut R Slotted rail (2×6, flat) 54″ 1 8 U-slots, 1¾″ × 3½″ deep L Ledger (2×4 flat on the wall) 66″ 1 square B Support block 4″ 3 square - 3
Ledger and support blocks
The ledger is a 2×4 flat on the wall, 66″ long, top edge at 40½″ (the rail sits on it). It runs 6″ past the rail at each end for hooks.
On the bench, screw 3 support blocks to the face of the ledger, flush with its top edge: one at each end of where the rail goes and one under every fourth tooth. Two 3″ screws from the back of the ledger into each block.
Mark where the studs fall on the ledger before you screw blocks on, so no block covers a stud screw location. - 4
Hang the ledger
Find the studs and snap a level line at 40½″. Hold the ledger to it, level it, and drive two ¼″ × 4″ structural screws into every stud it crosses, one high and one low (4–5 studs at 16″ on center, so up to 10 screws).
No studs where you want it? Screw a 2×6 backer across two studs first, then hang the ledger on that. Drywall anchors won't hold a rack full of shovels. - 5
Cut the slots and fit the rail
Lay out 8 slot centers on the rail, 6″ apart, the first 6″ from the end. Each slot is 1¾″ wide and 3½″ deep from the front edge.
- Drill a 1¾″ hole at each center, 2⅝″ in from the front edge. Clamp a scrap underneath so the bit doesn't blow out the back.
- Two straight saw cuts from the edge to the sides of each hole. The waste drops out and leaves a round-bottomed U-slot.
- Round every slot edge with sandpaper.
Set the rail on the ledger, back edge against the wall, ends lined up with the end blocks. 3″ screws down into the ledger every 6″ and two into each block.
- 6
Hooks and finish
Drill pilots and twist two utility hooks into each ledger extension: hose on one end, extension cords on the other.
A coat of exterior paint or poly keeps wet tools from staining and swelling the slots.
- 7
Done
8 long-handled tools standing upright, heads up, held by a rail at 42″. Park the heaviest (spade, fork, mattock) at the ends, near the end blocks.
Paint a short line on the wall or post above each slot and write what goes there. Tools come back to the right place when they have an address.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
1 board56% yield2×4 × 8′
1 board82% yieldHandles drop into U-shaped slots cut in the front edge of a flat 2×6 and stand on the floor below it. Most long-handled tools have 1⅛″–1⅜″ handles; the slots are 1¾″ so a gloved hand can drop one in without aiming.