Workbench Builder
Shopping list
Buy straight studs for the frame and legs. Get the best-faced sheet of plywood in the stack for the top; the shelf can be the ugly one.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ SPF board | 10 | $3.50 | $35.00 |
| ¾″ plywood, 4×8 sheet (BC or sanded) (top + shelf) | 2 | $52.00 | $104.00 |
| #9 × 3″ construction screws, 1-lb box (about 56) | 2 | $10.00 | $20.00 |
| #9 × 2½″ construction screws, 1-lb box (about 24) | 1 | $10.00 | $10.00 |
| #8 × 1⅝″ wood screws, 1-lb box (about 48) | 1 | $9.00 | $9.00 |
| Wood glue, 16 oz | 1 | $6.50 | $6.50 |
| Total | $184.50 |
Tools: miter saw or circular saw with a speed square, drill/driver, tape, framing square, 4′ level, at least four clamps, glue roller or a scrap of card to spread glue.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
10 boards76% yieldSheet goods
- P Top, ¾″ plywood: 1 × 72″ × 30″
- S Shelf, ¾″ plywood: 1 × 72″ × 29⅞″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Height is to the work surface. A good rule: stand straight, drop your hands, and measure floor to the base of your palm; that's a bench for planing and assembly. Doubled-2×4 tops come out a multiple of 3½″ deep.
- 1
Shopping list
Buy straight studs for the frame and legs. Get the best-faced sheet of plywood in the stack for the top; the shelf can be the ugly one.
Item Qty Each Total 2×4×8′ SPF board 10 $3.50 $35.00 ¾″ plywood, 4×8 sheet (BC or sanded) (top + shelf) 2 $52.00 $104.00 #9 × 3″ construction screws, 1-lb box (about 56) 2 $10.00 $20.00 #9 × 2½″ construction screws, 1-lb box (about 24) 1 $10.00 $10.00 #8 × 1⅝″ wood screws, 1-lb box (about 48) 1 $9.00 $9.00 Wood glue, 16 oz 1 $6.50 $6.50 Total $184.50 Tools: miter saw or circular saw with a speed square, drill/driver, tape, framing square, 4′ level, at least four clamps, glue roller or a scrap of card to spread glue.
- 2
Cut list
Cut the legs first, all from one stop-block setting: if one is ⅛″ short the bench rocks forever. Then frame parts, then rails.
Tag Part Length Qty Cut A Apron, front/back 72″ 2 square J Joist (frame end + intermediate) 27″ 4 square G Leg half (glue two per leg) 35¼″ 8 square R Lower rail, front/back 72″ 2 square E Lower rail, end 27″ 2 square P Top, ¾″ plywood (30″ wide) 72″ 1 square S Shelf, ¾″ plywood (29⅞″ wide) 72″ 1 notch 4½″ × 5″ at the 4 corners (cut them ⅛″ generous) - 3
Build the top frame
On a flat floor, stand the two aprons on edge 30″ apart outside to outside. Set the 4 joists between them: one flush at each end, the rest evenly spaced at 23½″ on center.
- Two 3″ screws through the apron into each joist end, predrilled 1″ from the ends so nothing splits.
- Keep the top edges flush: run your hand across every joint.
Square it now: diagonals equal within ⅛″. Push the long corner until they match, then tack a scrap across a corner to hold it. - 4
Make and fit the legs
Glue and screw two leg halves face to face for each of the 4 legs: a wavy bead of glue, clamp, six 2½″ screws staggered from both sides.
Flip the frame upside down. Each leg drops into an inside corner, tight against the apron and the joist, its end flush with the frame top (which is now on the floor).
- Two 3″ screws through the apron into the leg, two through the joist into the leg.
- Check each leg with a square to the frame in both directions before the second pair of screws.
- 5
Long lower rails
Mark 6″ up from the foot of every leg. Front and back rails go on the outside of the legs with their bottom edge on the mark, flush with the ends of the bench.
Two 3″ screws into each leg. These rails are what stop the bench walking across the floor when you plane or saw.
- 6
End rails and lower shelf
An end rail fits between the long rails at each end, against the outside of the end legs, at the same height: two screws through each long rail into its ends and two into each leg. Fit just one of them for now and flip the bench onto its feet.
The shelf is wider than the gap between the legs every way but one, so it has to go in through the open end before the second end rail closes it.
Notch the shelf plywood at each leg: 4½″ along the length × 5″ in from the edge at the four corners (end rail plus leg). Measure your actual legs first (laminated legs grow a hair) and cut the notches ⅛″ generous.
- Jigsaw the notches.
- Stand at the open end and slide the shelf in between the legs, tipped up on its long edge at about 50° so it clears them, until the far notches reach the far legs.
- Lay it down flat onto the rails, flush with the front.
- Fit the second end rail, then drive #8 × 1⅝″ screws every 10″ through the shelf into the front and back rails.
- 7
Plywood top
Lay the plywood good face up, flush to the front apron and both ends. If the frame is slightly out of square, split the error at the back.
- #8 × 1⅝″ screws every 8″ into the aprons and every joist; countersink them so nothing catches a workpiece.
- Ease all edges with sandpaper or a ⅛″ roundover.
- 8
Done
A 72″ × 30″ bench at 36″. Put it where it lives, check the top with a level both ways and shim any short leg before you start using it.
Two coats of wipe-on poly or boiled linseed oil on the top keeps glue and finish from sticking. Screw a power strip under the front apron while you're at it.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
10 boards76% yieldSheet goods
- P Top, ¾″ plywood: 1 × 72″ × 30″
- S Shelf, ¾″ plywood: 1 × 72″ × 29⅞″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Height is to the work surface. A good rule: stand straight, drop your hands, and measure floor to the base of your palm; that's a bench for planing and assembly. Doubled-2×4 tops come out a multiple of 3½″ deep.