Standing Desk Builder
Shopping list
Kiln-dried studs only, and pick them flat: a twisted leg makes a desk rock no matter how well it's built.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 stud, kiln-dried (legs, aprons, stretchers) | 8 | $3.98 | $31.84 |
| ¾″ × 4×8 plywood, birch or sanded (top and shelf) | 1 | $54.98 | $54.98 |
| 2½″ pocket-hole screws, coarse, 100-pack (side frames, long stretchers, leg glue-ups) | 1 | $8.98 | $8.98 |
| #9 × 3″ construction screws, 1-lb box (aprons to legs, center rail, risers) | 1 | $10.48 | $10.48 |
| Wood glue, 16 oz | 1 | $7.48 | $7.48 |
| Nail-in furniture glides, 1″, 8-pack (under the legs) | 1 | $4.98 | $4.98 |
| Tabletop fasteners (figure-8) with ⅝″ screws, 8-pack (top to aprons) | 1 | $5.98 | $5.98 |
| Wipe-on poly, 1 qt | 1 | $19.98 | $19.98 |
| Iron-on edge banding, ¾″ × 25′ | 1 | $9.98 | $9.98 |
| Total | $154.68 |
Tools: miter saw, pocket-hole jig, drill/driver, ¾″ Forstner or spade bit, clamps (at least four), square, sander, clothes iron for the edge banding.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
8 boards88% yieldSheet goods
- T Top: 1 × 60″ × 30″
- M Monitor shelf: 1 × 48″ × 9″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Legs are two 2×4s glued face to face. A full 2×4 apron under the top plus low stretchers on all four sides is what kills standing-desk wobble: you lean on these, so they have to be stiffer than a sitting desk.
- 1
Shopping list
Kiln-dried studs only, and pick them flat: a twisted leg makes a desk rock no matter how well it's built.
Item Qty Each Total 2×4×8 stud, kiln-dried (legs, aprons, stretchers) 8 $3.98 $31.84 ¾″ × 4×8 plywood, birch or sanded (top and shelf) 1 $54.98 $54.98 2½″ pocket-hole screws, coarse, 100-pack (side frames, long stretchers, leg glue-ups) 1 $8.98 $8.98 #9 × 3″ construction screws, 1-lb box (aprons to legs, center rail, risers) 1 $10.48 $10.48 Wood glue, 16 oz 1 $7.48 $7.48 Nail-in furniture glides, 1″, 8-pack (under the legs) 1 $4.98 $4.98 Tabletop fasteners (figure-8) with ⅝″ screws, 8-pack (top to aprons) 1 $5.98 $5.98 Wipe-on poly, 1 qt 1 $19.98 $19.98 Iron-on edge banding, ¾″ × 25′ 1 $9.98 $9.98 Total $154.68 Tools: miter saw, pocket-hole jig, drill/driver, ¾″ Forstner or spade bit, clamps (at least four), square, sander, clothes iron for the edge banding.
- 2
Cut list
Leg length is the desk height (42½″) minus the top (¾″) and the ¼″ glides. Cut all eight leg pieces from one stop-block setting.
Tag Part Length Qty Cut L Leg half (glue two per leg) 41½″ 8 square A Front / back apron 58″ 2 square S Side apron & side stretcher 18″ 4 square C Center rail 25″ 1 square F Long stretcher (footrest) 52″ 2 square T Top (30″ wide) 60″ 1 square R Shelf riser (on edge) 9″ 3 square M Monitor shelf (9″ wide) 48″ 1 square Rip the top first from the factory edge, then the 9″ shelf strip from what's left of the sheet. - 3
Laminate the legs
Glue two leg halves face to face, ends flush, best faces out. Clamp every 8″ and drive four 2½″ screws from the face that will point at the other side frame, so they don't show. (3″ screws would come out the far side of a 3″ leg.)
Make four. Scrape the squeeze-out when it's rubbery.
Check each leg for twist on a flat surface before the glue sets. Twist here is wobble later. - 4
Build the two side frames
Drill two pocket holes in each end of the four 18″ side pieces. Lay a front and a back leg on the bench, wide 3½″ faces flat on the bench and the glue-seam edges toward each other, 18″ apart. Fit an apron flush with the leg tops and a stretcher with its bottom edge 6″ up from the leg bottoms, both flush with the outside face of the legs.
Glue and pocket-screw. Build the second frame on top of the first.
Check: square each frame by its diagonals before the glue grabs. - 5
Connect the frames
Stand the side frames up and join them with the 58″ front and back aprons across the outside face of the legs, flush at the top, two 3″ screws into each leg plus glue.
- Long stretchers (52″) pocket-screw between the legs 6″ up. The front one is your footrest.
- Center rail (25″) between the two long aprons at mid-length, flush on top, two 3″ screws through each apron into its ends. It carries the middle of the top.
Check: stand it on a flat floor. All four feet down, diagonals of the top equal. Push on a corner: it shouldn't move. - 6
Attach the top
Iron edge banding onto all four edges of the plywood top, trim, and sand.
Center the top with 1″ overhang all round. Fasten it with the eight figure-8 tabletop fasteners: recess each one flush into the top edge of an apron with a ¾″ Forstner or spade bit, three along each long apron and one on each side apron, then screw up into the top with the ⅝″ screws from the pack. Don't use the 2½″ pocket screws here; they'd come through a ¾″ top.
- 7
Monitor shelf
Three 9″ 2×4 risers on edge, flush with the back edge of the top: one 6″ in from each end and one in the middle so the plywood shelf can't sag. Screw up through the desk top into each riser from below (two 3″ screws) so nothing shows on the work surface.
The 48″ shelf goes on top, ends flush with the outer risers: glue and two 3″ screws down into each riser, countersunk.
Flip the desk on a blanket and tap a nail-in glide into the bottom center of each leg.
With a monitor on the shelf, the top of the screen should sit at or just below eye level. - 8
Done
A 60″ × 30″ standing desk at 42½″. Sand to 180 and wipe on three coats of poly, top first. Let it cure a week before heavy use.
Get an anti-fatigue mat. Standing on a hard floor all day is what makes people quit standing desks, not the desk.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
8 boards88% yieldSheet goods
- T Top: 1 × 60″ × 30″
- M Monitor shelf: 1 × 48″ × 9″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Legs are two 2×4s glued face to face. A full 2×4 apron under the top plus low stretchers on all four sides is what kills standing-desk wobble: you lean on these, so they have to be stiffer than a sitting desk.