Sawhorse Builder
Shopping list
Sawhorses are the project that pays for itself: you'll use them to build everything else. Any straight stud works; this is where cull-cart lumber shines.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 stud, untreated SPF | 9 | $3.50 | $31.50 |
| #9 × 3″ construction screws, 1-lb box (about 96) | 1 | $10.00 | $10.00 |
| Total | $41.50 |
Tools: miter saw (set to 16°) or circular saw with a speed square, drill/driver, tape, pencil, clamps.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
9 boards79% yieldThe legs lean out 16° to the sides only, a lean set by the I-beam itself: each leg sits under the cap and against the edge of the bottom plate. Seen from the side they are plumb, which is what lets two horses carry a sheet of plywood without wobbling. Prices are per board at the price you enter.
- 1
Shopping list
Sawhorses are the project that pays for itself: you'll use them to build everything else. Any straight stud works; this is where cull-cart lumber shines.
Item Qty Each Total 2×4×8 stud, untreated SPF 9 $3.50 $31.50 #9 × 3″ construction screws, 1-lb box (about 96) 1 $10.00 $10.00 Total $41.50 Tools: miter saw (set to 16°) or circular saw with a speed square, drill/driver, tape, pencil, clamps.
- 2
Cut list
Quantities cover all 2 sawhorses. Legs get a 16° cut on both ends, parallel (the leg looks like a long thin parallelogram), so the top sits flat against the underside of the cap and the foot sits flat on the floor.
Tag Part Length Qty Cut B Beam (on edge) 36″ 2 square C Cap (flat, on top of beam) 36″ 2 square P Bottom plate (flat, under the beam) 36″ 2 square L Leg 32⅜″ 8 16° both ends, parallel (long point to long point) S Side stretcher 32″ 4 square G End gusset 19¾″ 4 square, a little long (trim flush after) Leg length is measured along the long edge. Set a stop block on the saw and cut all 8 legs from one setting so every horse sits level. - 3
Make the I-beam top
The top is three 2×4s in an I: the cap lies flat on top, the beam stands on edge under it, and the bottom plate lies flat under the beam. Cap and plate are both centered on the beam, so each sticks out 1″ past it on both sides.
- Stand the beam on edge on the bench, lay the cap flat on it, centered, ends flush, and screw down through the cap into the beam every 8″ (start 1″ from each end).
- Flip it over so the cap is on the bench and the beam sticks up. Lay the plate on the beam, centered, ends flush, and screw it down the same way.
- Keep all the ends flush; the legs reference off them.
- Glue here is worth it if you have it.
- Leave it upside down (cap on the bench) for the legs. Overall it's 6½″ tall.
- 4
Attach the legs
This is the joint that holds everything. Each leg drops into the pocket on the side of the I: its angled top end butts tight against the underside of the cap, its wide face touches the beam right under the cap and leans out over the edge of the bottom plate. The plate sticks out 1″ past the beam, and that is what sets the lean (16°); you don't have to measure it.
The cap carries the load straight down into the end grain of the legs; the screws just keep them there.
- With the top upside down (cap on the bench), set a leg in the pocket, 2″ in from the end of the beam, top cut flat on the cap, wide face tight against the edge of the plate.
- Clamp it and drive four 3″ screws: two through the leg into the edge of the plate, and two near the top of the leg into the beam. Stagger them so they don't split the leg.
- Same leg on the other side of the beam at that end, then both legs at the far end. Opposite legs make an upside-down V seen from the end.
The leg only touches the beam at the very top; 3½″ lower, at the plate, there is a 1″ wedge of air between them. That's right. The top outside corner of each leg also sticks out about ½″ past the edge of the cap; don't trim it.
Check: stand it up. All four feet should touch. If one rocks, that leg isn't tight up under the cap — back the screws out, push it up, and re-drive. - 5
Side stretchers
On each side, screw a 32″ 2×4 flat across the outside faces of the two legs, about 12¼″ off the floor (center of the board). Its ends line up with the outside edges of the legs.
It lies flat on the legs, so it leans the same 16° they do. Two 3″ screws into each leg.
Measure the actual distance over the legs at that height before you cut; small lean differences show up here.
- 6
End gussets
At each end, a 2×4 runs across the end edges of the two legs at the stretcher height, covering the ends of both stretchers. Two screws into each leg and one into each stretcher end, then trim the gusset flush with the outside of the stretchers.
This closes the triangle at each end. The horse should now feel like one piece.
- 7
Build the rest
Repeat for the other 1. Use the first one as a jig: clamp the new legs to it to match the lean.
Set them side by side and lay a straight board across both caps; shim or trim a foot until the board sits flat.
- 8
Done
2 sawhorses at 32″. The cap is sacrificial: when it's chewed up from saw cuts, back out the screws and swap in a new 2×4.
Lay a few 8′ 2×4s across a pair of them and you have a 36″ × 8′ work table. Clamp a sheet of plywood on top for a full bench.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
9 boards79% yieldThe legs lean out 16° to the sides only, a lean set by the I-beam itself: each leg sits under the cap and against the edge of the bottom plate. Seen from the side they are plumb, which is what lets two horses carry a sheet of plywood without wobbling. Prices are per board at the price you enter.