Platform Bed Builder
Shopping list
Pick the straightest, driest studs in the bin; this one lives indoors and any twist shows. Kiln-dried "KD" or "prime" studs are worth the extra dollar here.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×6×8, kiln dried, rim | 4 | $7.00 | $28.00 |
| 2×4×8 stud, kiln dried, cleats, legs, center beam | 5 | $3.50 | $17.50 |
| 1×4×8 common board, slats | 13 | $4.50 | $58.50 |
| #9 × 2½″ wood screws, 1-lb box (about 92) | 1 | $10.98 | $10.98 |
| #9 × 3″ wood screws, 1-lb box (about 20, for the rim corners and beam ends) | 1 | $10.98 | $10.98 |
| #8 × 1⅝″ wood screws, 1-lb box (slats) (about 49) | 1 | $9.98 | $9.98 |
| Wood glue, 8 oz | 1 | $4.98 | $4.98 |
| Felt pads for the legs, 1 pack | 1 | $5.98 | $5.98 |
| Total | $146.90 |
Tools: miter saw, drill/driver, countersink bit, tape, speed square, clamps, sander (the only build on this site where sanding matters).
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
4 boards77% yield2×4 × 8′
5 boards85% yield1×4 × 8′
13 boards65% yieldThe rim is a 2×6 on edge with 2×4 cleats glued and screwed inside it; slats rest on the cleats 2″ below the rim top, so the mattress is held in. L-shaped 2×4 legs sit inside the corners and at mid-length, lapping the rim by a full 3½″, and full and wider beds get a center beam on its own legs. 3″ slat gaps let a foam mattress breathe.
- 1
Shopping list
Pick the straightest, driest studs in the bin; this one lives indoors and any twist shows. Kiln-dried "KD" or "prime" studs are worth the extra dollar here.
Item Qty Each Total 2×6×8, kiln dried, rim 4 $7.00 $28.00 2×4×8 stud, kiln dried, cleats, legs, center beam 5 $3.50 $17.50 1×4×8 common board, slats 13 $4.50 $58.50 #9 × 2½″ wood screws, 1-lb box (about 92) 1 $10.98 $10.98 #9 × 3″ wood screws, 1-lb box (about 20, for the rim corners and beam ends) 1 $10.98 $10.98 #8 × 1⅝″ wood screws, 1-lb box (slats) (about 49) 1 $9.98 $9.98 Wood glue, 8 oz 1 $4.98 $4.98 Felt pads for the legs, 1 pack 1 $5.98 $5.98 Total $146.90 Tools: miter saw, drill/driver, countersink bit, tape, speed square, clamps, sander (the only build on this site where sanding matters).
- 2
Cut list
The rim's inside is 82″ × 62″: 1″ over the mattress on every side so sheets tuck. The 2×6 side rails run the full length; the head and foot rails fit between them. Everything else is 2×4 and 1×4.
Tag Part Length Qty Cut R1 Side rail, 2×6 on edge 85″ 2 square R2 Head / foot rail, 2×6 on edge (between the side rails) 62″ 2 square C Slat cleat, 2×4 on edge (between the legs) 35¾″ 4 square L Leg, 2×4 (two per leg: an L at the corners, a T at mid-length) 12″ 12 square B Center beam, 2×4 on edge 82″ 1 square L2 Center-beam leg, 2×4 (beside the beam) 12″ 3 square S Slat, 1×4 flat 62″ 13 square Sand everything to 120 grit before assembly, and ease the rim's top edges with a sanding block. Shins will thank you. - 3
Rim and cleats
Join the four 2×6 rails into a rectangle on a flat floor, head and foot rails between the sides, with glue and three 3″ screws through the side rail into each rail end. Pilot-drill and countersink every screw.
Then glue and screw the four 35¾″ cleats on edge to the inside of the side rails, bottoms flush with the rail bottoms, which puts their tops 2″ below the rim top. On each side: one cleat starts 3½″ from the head rail, then a 3½″ gap at mid-length, then the second cleat stops 3½″ short of the foot rail. The gaps are where the legs go.
- Screw from the inside, through the cleat into the rail, with a 2½″ screw every 8″ in a zigzag. Nothing shows on the outside and nothing pokes through.
- The cleats carry the slats, so don't skip the glue.
Check: diagonals equal. A bed that's out of square shows the instant the mattress goes on. - 4
Legs
Each leg is two 12″ 2×4s glued and screwed together with four 2½″ screws. The four corner legs are Ls: the edge of one piece against the face of the other, flush along one side. The two mid legs are Ts: the second piece centered on the first.
Flip the rim upside down. Stand an L in each inside corner, one piece flat against the side rail and the other flat against the head or foot rail, and a T in each cleat gap with its flat piece against the side rail. Leg tops go flush with the cleat tops, 2″ short of the rim top: with the rim upside down, stand each leg on a 2″ block while you screw it.
- Glue, then three 2½″ screws in a triangle through each leg piece into the rail it lies against, driven from the inside. Every leg laps the rail by 3½″; that lap is what keeps the bed from wobbling.
- The cleat ends should butt tight against the legs.
- Felt pads on the bottoms before you flip it back over.
- 5
Center beam
The 82″ center beam goes on edge down the middle, between the head and foot rails, its top flush with the cleat tops and its bottom flush with the rim bottom (8½″ off the floor). Two 3″ screws through the head and foot rails into each end.
Screw a 12″ 2×4 leg flat against its side at the head, middle and foot, tops flush with the beam: glue and three 2½″ screws through each leg into the beam. This is what stops a queen from sagging in the middle.
- 6
Slats
Lay the 13 slats across the cleats and center beam, first one tight to the head rail, about 3″ apart (a 3″ spacer block helps).
One 1⅝″ screw at each end into the cleat and one into the beam; 1×4s can twist otherwise.
- 7
Finish
Wipe-on poly or Danish oil, two coats, after a final 180-grit sand. Or paint it. Let it cure 48 hours somewhere ventilated before the mattress goes on.
- 8
Done
Queen platform: rim top 14″, slats at 12¾″, 8½″ of clear space under the rim.
A foam mattress needs the 3″ slat gaps to breathe; a spring mattress is fine on anything. If it ever squeaks, it's a slat rubbing a cleat: a strip of felt tape fixes it.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
4 boards77% yield2×4 × 8′
5 boards85% yield1×4 × 8′
13 boards65% yieldThe rim is a 2×6 on edge with 2×4 cleats glued and screwed inside it; slats rest on the cleats 2″ below the rim top, so the mattress is held in. L-shaped 2×4 legs sit inside the corners and at mid-length, lapping the rim by a full 3½″, and full and wider beds get a center beam on its own legs. 3″ slat gaps let a foam mattress breathe.