Picnic Table Builder
Shopping list
Everything is ground-contact pressure-treated. Pick the straightest, driest boards in the pile. Wet PT shrinks, so buy a week ahead and sticker it flat in the shade if you can.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×6×8 pressure-treated (top, seats, legs, seat supports) | 12 | $9.48 | $113.76 |
| 2×4×8 pressure-treated (cleats and braces) | 2 | $5.98 | $11.96 |
| ⅜″ × 4″ galvanized carriage bolt, washer & nut (2 per leg at the cleat, 2 per leg at the seat support) | 16 | $1.65 | $26.40 |
| 3″ exterior deck screws, 1-lb box (about 62 needed; ~70 per box) | 1 | $11.98 | $11.98 |
| Exterior stain / sealer, 1 qt (after the wood dries) | 1 | $18.98 | $18.98 |
| Total | $183.08 |
Tools: circular saw or miter saw (30°), drill/driver, ⅜″ spade or auger bit, 9⁄16″ socket or wrench, speed square, tape, chalk line, two clamps, 16d nails for spacers, sander.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
12 boards79% yield2×4 × 8′
2 boards68% yieldLegs lean 30° from plumb, bolted between a 2×4 cleat under the top and a 2×6 seat support. Adult sizes put the top at 30″ and the seats at 17½″, the standard picnic-table rise. Everything is ground-contact pressure-treated with exterior screws and galvanized bolts.
- 1
Shopping list
Everything is ground-contact pressure-treated. Pick the straightest, driest boards in the pile. Wet PT shrinks, so buy a week ahead and sticker it flat in the shade if you can.
Item Qty Each Total 2×6×8 pressure-treated (top, seats, legs, seat supports) 12 $9.48 $113.76 2×4×8 pressure-treated (cleats and braces) 2 $5.98 $11.96 ⅜″ × 4″ galvanized carriage bolt, washer & nut (2 per leg at the cleat, 2 per leg at the seat support) 16 $1.65 $26.40 3″ exterior deck screws, 1-lb box (about 62 needed; ~70 per box) 1 $11.98 $11.98 Exterior stain / sealer, 1 qt (after the wood dries) 1 $18.98 $18.98 Total $183.08 Tools: circular saw or miter saw (30°), drill/driver, ⅜″ spade or auger bit, 9⁄16″ socket or wrench, speed square, tape, chalk line, two clamps, 16d nails for spacers, sander.
- 2
Cut list
Legs get a 30° cut on both ends, parallel, so the top sits flat under the top boards and the foot sits flat on the ground. Measure the 36⅛″ leg long point to long point.
Tag Part Length Qty Cut T Top board 72″ 5 square S Seat board 72″ 4 square L Leg 36⅛″ 4 30° both ends, parallel P Seat support 58″ 2 45° corner clips (optional) C Top cleat 25½″ 3 45° corner clips (optional) B Diagonal brace 26¾″ 2 32° both ends, parallel Cut one leg, check it against a full-size layout (Step 3), then use it as the pattern for the other three. Brace length is long point to long point; cut it a hair long and test-fit. - 3
Build the two A-frames
Draw a full-size layout on the driveway or a sheet of plywood: a line for the underside of the top, a floor line 28½″ below it, and the center line. Each leg's centerline lands 7¼″ off center at the top and 23¾″ at the floor.
- Lay a 25½″ cleat on edge along the top line.
- Set two legs on it, tops tight to the top line, feet on the floor line. The cleat is on the outside face of the legs.
- Clamp, drill ⅜″ through cleat and leg, and drive two carriage bolts per leg, set on a diagonal at least 1″ from every edge. Heads on the cleat side.
Check: both legs at the same angle, both feet exactly on the floor line, and the foot-to-foot spread equal on both frames. Build the second frame right on top of the first to match it. - 4
Seat supports
Bolt a 58″ 2×6 seat support on edge across the inside face of the legs, top edge 16″ above the floor line, centered so it overhangs equally both sides.
Two carriage bolts per leg, staggered diagonally so they don't split the leg. Now each frame is a rigid A with a crossbar.
Bolt heads face out where knees and kids are. Nuts and washers go on the inside. - 5
Stand the frames and lay the top
Stand both frames upright, cleats facing out, 52″ apart outside to outside (10″ in from each end of the top).
- Lay the 5 top boards across the cleats, crown up, with 16d nails as ¼″ spacers. Flush the ends with a straightedge.
- Two 3″ screws per board per cleat, ¾″ in from the edges, pilot holes near board ends.
- Set the third cleat on edge under the middle of the top and screw down through every top board into it.
Check: measure the top's diagonals. Equal means square; rack the frames until they match before the last screws go in. - 6
Diagonal braces
Each brace runs along the centerline from the middle of a seat support up to the center cleat at about 32°. They stop the table racking end to end.
Both ends are cut plumb. The lower end sits flat on the inside face of the seat support; the upper end sits flat on the center cleat with its long point tucked tight under the top boards.
Hold the brace in place, scribe the actual angles if they don't sit tight, then four 3″ screws at each end, toed through the brace into the seat support and into the center cleat. Pilot first so the ends don't split.
- 7
Seat boards
Two 2×6 seat boards per side on the seat supports, inner edge 4″ outside the table edge, ¼″ gap between them, ends flush with the top.
Two screws per board per support. Countersink every head; this is where shorts and bare legs go.
- 8
Done
6′ table, 28½″ top, seats 6. Ease every edge and corner with a sander or a block plane, and knock the corners off the seat-support and cleat ends.
Let the pressure-treated lumber dry until a drop of water soaks in (often 1–3 months), then seal it. Re-snug the bolts after the first season; PT shrinks as it dries.
Set it on level ground or pavers. On soft lawn the feet sink unevenly and the bolts take all the racking.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
12 boards79% yield2×4 × 8′
2 boards68% yieldLegs lean 30° from plumb, bolted between a 2×4 cleat under the top and a 2×6 seat support. Adult sizes put the top at 30″ and the seats at 17½″, the standard picnic-table rise. Everything is ground-contact pressure-treated with exterior screws and galvanized bolts.