Outdoor Bench Builder
Shopping list
Pressure-treated if it lives on grass or a patio year-round; cedar if it's under a porch and you want it to look like furniture. Pick dry, straight boards for the seat slats; wet treated lumber shrinks and opens the gaps.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ pressure-treated (frame) | 5 | $4.98 | $24.90 |
| 2×6×8′ pressure-treated (seat and back slats) | 5 | $7.98 | $39.90 |
| #9 × 3″ exterior screws, 1-lb box (aprons, center support, stretcher) | 1 | $10.98 | $10.98 |
| #9 × 2½″ exterior screws, 1-lb box (~75) (end frames and slats, about 46) | 1 | $10.98 | $10.98 |
| Exterior wood glue, 8 oz | 1 | $5.98 | $5.98 |
| ⅜″ × 4″ galvanized carriage bolt, nut + washer (upper bolt, post + leg) | 2 | $1.48 | $2.96 |
| ⅜″ × 5½″ galvanized carriage bolt, nut + washer (lower bolt, post + leg + rail) | 2 | $1.78 | $3.56 |
| Exterior stain / sealer, 1 qt (optional) | 1 | $16.98 | $16.98 |
| Total | $116.24 |
Tools: miter saw (set to 15° for the post ends), drill/driver, ⅜″ spade or auger bit, socket wrench, clamps, speed square, sander with 120 grit.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
5 boards64% yield2×4 × 8′
5 boards79% yieldThe backrest posts lean back 15° and bolt to the outside of the legs. Prices are per 8′ board at the price you enter.
- 1
Shopping list
Pressure-treated if it lives on grass or a patio year-round; cedar if it's under a porch and you want it to look like furniture. Pick dry, straight boards for the seat slats; wet treated lumber shrinks and opens the gaps.
Item Qty Each Total 2×4×8′ pressure-treated (frame) 5 $4.98 $24.90 2×6×8′ pressure-treated (seat and back slats) 5 $7.98 $39.90 #9 × 3″ exterior screws, 1-lb box (aprons, center support, stretcher) 1 $10.98 $10.98 #9 × 2½″ exterior screws, 1-lb box (~75) (end frames and slats, about 46) 1 $10.98 $10.98 Exterior wood glue, 8 oz 1 $5.98 $5.98 ⅜″ × 4″ galvanized carriage bolt, nut + washer (upper bolt, post + leg) 2 $1.48 $2.96 ⅜″ × 5½″ galvanized carriage bolt, nut + washer (lower bolt, post + leg + rail) 2 $1.78 $3.56 Exterior stain / sealer, 1 qt (optional) 1 $16.98 $16.98 Total $116.24 Tools: miter saw (set to 15° for the post ends), drill/driver, ⅜″ spade or auger bit, socket wrench, clamps, speed square, sander with 120 grit.
- 2
Cut list
Everything is square-cut except the backrest posts: 15° on both ends, parallel, so the bottom sits level and the top is horizontal. Seat slats run the full 60″.
Tag Part Length Qty Cut L Leg, 2×4 16½″ 4 square S Seat support, 2×4 14″ 3 square R Lower end rail, 2×4 17″ 2 square A Apron, 2×4 57″ 2 square T Long stretcher, 2×4 54″ 1 square K Seat slat, 2×6 60″ 3 square P Backrest post, 2×4 33⅛″ 2 15° both ends, parallel (long point to long point) B Back slat, 2×6 63″ 2 square - 3
Build the end frames
Each end is two 16½″ legs, 17″ apart outside to outside, joined by a seat support at the top and a rail 4″ off the floor, both on the inside face.
- Seat support: top edge flush with the leg tops, centered front to back (1½″ in from each edge, where the aprons will go).
- Lower rail: flush with the front and back edges of the legs.
- Glue plus two 2½″ screws at every joint (two 2×4s face to face are 3″ thick, so a 3″ screw would come out the far side). Check the frame square with a speed square at each corner.
- 4
Aprons and stretcher
Stand the frames up and run a 57″ apron between the legs, front and back, tops flush with the seat supports. Then the 54″ stretcher between the lower rails, centered.
- Drive two 3″ screws from the outside of each leg into the apron end, and two through the apron into the end of the seat support.
- Add a third seat support at the center, between the aprons. At this length the slats need it.
- Diagonals across the top should match within ⅛″.
- 5
Seat slats
3 2×6 slats, ¼″ gaps, flush with the front and back of the frame and with the ends.
- Two 2½″ screws into every support, pre-drilled near the ends.
- Sand or round over the front edge of the front slat; it's what the back of your knees touch.
- 6
Backrest
Clamp a 33⅛″ post to the outside face of each back leg, bottom end level and 4″ off the floor, leaning back 15° (the parallel end cuts make it easy: when the bottom is level, the lean is right). At the bottom the post's front corner sticks out about 1⅜″ in front of the leg; at the top of the leg its back edge is about 2″ behind it.
- Drill two ⅜″ holes square through the post and leg on the post's centerline, 6″ and 12″ off the floor. The low one also goes through the lower end rail: use the 5½″ bolt there, the 4″ bolt in the high one. Heads outside, washer and nut inside, snug but don't crush the wood.
- 2 back slats across the front face of the posts, the top one ½″ down from the post tops, 1½″ gaps, ends flush with the outside faces of the posts. Three 2½″ screws per post.
- Sit in it before the last slat. Move the lower slat up or down to suit your back.
Use the carriage bolts. Screws alone in a leaning backrest work loose within a season. - 7
Done
A 5′ bench, 18″ to the seat. Ease every sharp edge with 120 grit, then stain once the treated lumber is dry (a drop of water soaks in instead of beading).
On grass, set the feet on pavers. Plastic or rubber glides under the legs on a patio stop the end grain from wicking up water.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
5 boards64% yield2×4 × 8′
5 boards79% yieldThe backrest posts lean back 15° and bolt to the outside of the legs. Prices are per 8′ board at the price you enter.