Miter Saw Station Builder
Shopping list
Before you buy anything, measure your saw: set it on a flat bench, lay a straightedge across the table, and measure down to the bench. This plan uses 3¾″. Change it above if yours is different.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ SPF board | 14 | $3.50 | $49.00 |
| ¾″ plywood, 4×8 sheet (BC or sanded) (tops, shelves, saw deck) | 2 | $52.00 | $104.00 |
| #9 × 3″ construction screws, 1-lb box (about 120) | 3 | $10.00 | $30.00 |
| #9 × 2½″ construction screws, 1-lb box (about 60) | 1 | $10.00 | $10.00 |
| #8 × 1⅝″ wood screws, 1-lb box (about 69) | 1 | $9.00 | $9.00 |
| ¼″-20 × 2″ hex bolt, nut + 2 fender washers (saw feet) | 4 | $1.10 | $4.40 |
| Wood glue, 16 oz | 1 | $6.50 | $6.50 |
| Total | $212.90 |
Tools: circular saw or the miter saw itself (before it moves in), drill/driver, tape, 4′ level, 6′ straightedge or a straight 2×4, clamps, jigsaw.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
14 boards91% yieldSheet goods
- P Wing top, ¾″ plywood: 2 × 36″ × 23⅞″
- S Wing shelf, ¾″ plywood: 2 × 36″ × 23⅞″
- D Saw deck, ¾″ plywood: 1 × 26″ × 23⅞″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
The saw sits on a plywood platform dropped exactly its table height below the wing tops. Measure your own saw with a straightedge across the table and a tape down to the bench; the presets are typical, not gospel.
- 1
Shopping list
Before you buy anything, measure your saw: set it on a flat bench, lay a straightedge across the table, and measure down to the bench. This plan uses 3¾″. Change it above if yours is different.
Item Qty Each Total 2×4×8′ SPF board 14 $3.50 $49.00 ¾″ plywood, 4×8 sheet (BC or sanded) (tops, shelves, saw deck) 2 $52.00 $104.00 #9 × 3″ construction screws, 1-lb box (about 120) 3 $10.00 $30.00 #9 × 2½″ construction screws, 1-lb box (about 60) 1 $10.00 $10.00 #8 × 1⅝″ wood screws, 1-lb box (about 69) 1 $9.00 $9.00 ¼″-20 × 2″ hex bolt, nut + 2 fender washers (saw feet) 4 $1.10 $4.40 Wood glue, 16 oz 1 $6.50 $6.50 Total $212.90 Tools: circular saw or the miter saw itself (before it moves in), drill/driver, tape, 4′ level, 6′ straightedge or a straight 2×4, clamps, jigsaw.
- 2
Cut list
Two identical wings plus the saw platform. Cut all 16 leg halves from one stop-block setting. The plywood rips to 23⅞″ so two strips come out of one sheet.
Tag Part Length Qty Cut A Wing apron, front/back 36″ 4 square J Wing joist 21″ 6 square G Leg half (glue two per leg) 35¼″ 16 square R Lower rail, front/back 36″ 4 square E Lower rail, end 21″ 4 square F Wing fence (on edge) 36″ 2 square C Platform cleat 21″ 2 square K Platform rail 23″ 2 square P Wing top, ¾″ plywood (23⅞″ wide) 36″ 2 square S Wing shelf, ¾″ plywood (23⅞″ wide) 36″ 2 notch 4½″ × 5″ at the outer corners, 3″ × 5″ at the inner corners (cut them ⅛″ generous) D Saw deck, ¾″ plywood (23⅞″ wide) 26″ 1 square - 3
Build two wing frames
Each wing frame is two 36″ aprons on edge with 3 joists between them: one flush at the outer end, one stopping 3″ short of the inner end (the 3″-thick inner legs fill that space), one in the middle.
- Two 3″ screws through the apron into each joist end, predrilled.
- Square by diagonals. Build the second frame on top of the first so they match.
- 4
Legs
Glue and screw leg halves into 8 doubled legs (35¼″). With each frame upside down, set the outer legs inside the corners against the end joist, and the inner legs flush with the inner end of the aprons, tight to the inner joist.
- Two 3″ screws through the apron and two through the joist into every leg.
- Square each leg to the frame both ways before the second pair of screws.
The flush inner legs are what the saw platform hangs on. Keep their inside faces straight and flush with the apron ends. - 5
Lower rails and shelves
Front and back rails 6″ up from the floor (bottom edge), outside the legs, flush with both wing ends. Two 3″ screws into each leg.
End rails fit between the long rails at the same height: at the outer end against the outside face of the legs, at the inner end against the inside face of the legs, so the saw-side faces stay clear for the platform. Two screws through the long rail into each end-rail end, two into each leg. Fit the inner one now and leave the outer one off until the shelf is in.
Flip each wing onto its feet. Notch the shelf plywood 4½″ × 5″ at the outer corners (end rail plus leg) and 3″ × 5″ at the inner corners, ⅛″ generous.
- Slide the shelf in through the open outer end, tipped up on its long edge at about 50° so it passes between the legs.
- Lay it flat on the rails, flush with the front.
- Fit the outer end rail, then #8 × 1⅝″ screws every 10″ through the shelf into the rails.
- 6
Hang the saw platform
Stand the wings 26″ apart (the saw bay), fronts in line. Clamp a straight 2×4 across both frames to hold them while you work.
- Build the platform frame on the floor first: the two platform rails (23″) between the two cleats, flush on top, each set 3½″ in from the cleat ends so those ends stay clear for the screws into the legs. Two 3″ screws through each cleat into each rail end.
- Mark the saw-side faces of the inner legs: the cleat tops sit 3¾″ below the top of the wing frames (31½″ off a flat floor). That's your saw's table height plus the ¾″ deck, minus the ¾″ wing top that isn't on yet.
- Lift the frame into the bay, clamp the cleats on the marks, and drive two 3″ screws through each cleat end into the leg behind it (8 in all), predrilled.
- Saw deck plywood on top, #8 × 1⅝″ screws every 6″ into the cleats and rails.
Measure down from a straightedge laid across both wing frames rather than up from the floor; floors aren't flat, frames are. - 7
Wing tops
Plywood on each wing, flush to the front and both ends, #8 × 1⅝″ screws every 8″ into the aprons and joists. Countersink every head: boards slide across this surface all day.
Ease the inner edges next to the saw with sandpaper so stock doesn't catch as it slides on.
- 8
Set the saw and the wing fences
Set the saw on the deck, centered in the bay. Lay a 6′ straightedge across the saw table onto both wings: it should touch everywhere. If the table is low, shim under the feet with hardboard; if high, you measured wrong, so back out the cleat screws and re-set them.
- Mark the foot holes, drill ¼″ through the deck, and bolt the saw down with ¼″ × 2″ bolts, a fender washer on top and bottom, and nuts underneath. Bolts come out when the saw goes to a job site.
- Wing fences: a straight 2×4 on edge along each wing, its face in line with the saw fence (about 14″ back from the front edge). Run a straightedge along the saw fence, clamp each wing fence to it, then drive 2½″ screws up through the plywood into the fence every 8″.
- 9
Done
8′ 2″ long, with 36″ of support either side of the saw, all in one plane with its table.
Stick a self-adhesive tape measure on each wing fence, reading from the blade, and a flip stop clamped to it turns repeat cuts into a one-person job.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
14 boards91% yieldSheet goods
- P Wing top, ¾″ plywood: 2 × 36″ × 23⅞″
- S Wing shelf, ¾″ plywood: 2 × 36″ × 23⅞″
- D Saw deck, ¾″ plywood: 1 × 26″ × 23⅞″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
The saw sits on a plywood platform dropped exactly its table height below the wing tops. Measure your own saw with a straightedge across the table and a tape down to the bench; the presets are typical, not gospel.