Kids' Loft Bed Builder
Shopping list
Indoor furniture for a kid's bedroom: use untreated kiln-dried lumber, never pressure-treated. Pick straight, dry boards with no cracks at the ends; the rails are the structure.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 stud, kiln-dried (posts, ledgers, slats, ladder) | 19 | $3.98 | $75.62 |
| 2×6×8, kiln-dried (rails and guard boards) | 15 | $6.98 | $104.70 |
| ⅜″ × 6″ carriage bolt, washer & nut (end rails, end guards, ladder) | 22 | $1.98 | $43.56 |
| ⅜″ × 5″ carriage bolt, washer & nut (long rails below the ledger, back lower rail) | 6 | $1.78 | $10.68 |
| ⅜″ × 7″ carriage bolt, washer & nut (through ledger, long rail and post; ladder) | 6 | $2.28 | $13.68 |
| #9 × 3″ construction screws, 1-lb box (~75) (slats, guards, rungs · about 108) | 2 | $10.48 | $20.96 |
| #9 × 2½″ construction screws, 1-lb box (~95) (post glue-ups, ledgers · about 76) | 1 | $10.48 | $10.48 |
| Wood glue, 16 oz | 1 | $7.48 | $7.48 |
| 5/16″ × 8″ structural wood screw, washer head (wall anchors: through guard and spacer block into a stud) | 4 | $3.48 | $13.92 |
| Paint or poly, 1 qt | 1 | $19.98 | $19.98 |
| Total | $321.06 |
Tools: miter saw, circular saw (for the rung dados), chisel, drill/driver, ⅜″ × 12″ bit, 9/16″ socket, 4′ level, square, clamps, stud finder, sander with 120/180. And a helper for standing it up.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
15 boards62% yield2×4 × 8′
19 boards81% yieldBuilt to the spirit of the U.S. bunk-bed safety standard (16 CFR 1513 / ASTM F1427): guard rails on all four sides, rail tops at least 5″ above the mattress, every opening in the guard 3½″ or less, a ladder opening no wider than 15″, and a mattress pocket only 1″ bigger than the mattress so there's no gap to slip into. Not for children under 6 on the upper deck.
- 1
Shopping list
Indoor furniture for a kid's bedroom: use untreated kiln-dried lumber, never pressure-treated. Pick straight, dry boards with no cracks at the ends; the rails are the structure.
Item Qty Each Total 2×4×8 stud, kiln-dried (posts, ledgers, slats, ladder) 19 $3.98 $75.62 2×6×8, kiln-dried (rails and guard boards) 15 $6.98 $104.70 ⅜″ × 6″ carriage bolt, washer & nut (end rails, end guards, ladder) 22 $1.98 $43.56 ⅜″ × 5″ carriage bolt, washer & nut (long rails below the ledger, back lower rail) 6 $1.78 $10.68 ⅜″ × 7″ carriage bolt, washer & nut (through ledger, long rail and post; ladder) 6 $2.28 $13.68 #9 × 3″ construction screws, 1-lb box (~75) (slats, guards, rungs · about 108) 2 $10.48 $20.96 #9 × 2½″ construction screws, 1-lb box (~95) (post glue-ups, ledgers · about 76) 1 $10.48 $10.48 Wood glue, 16 oz 1 $7.48 $7.48 5/16″ × 8″ structural wood screw, washer head (wall anchors: through guard and spacer block into a stud) 4 $3.48 $13.92 Paint or poly, 1 qt 1 $19.98 $19.98 Total $321.06 Tools: miter saw, circular saw (for the rung dados), chisel, drill/driver, ⅜″ × 12″ bit, 9/16″ socket, 4′ level, square, clamps, stud finder, sander with 120/180. And a helper for standing it up.
- 2
Cut list
All cuts square. The long pieces are 76″ so the mattress pocket is 76 × 39″: ½″ of play around a 75 × 38″ mattress. Ladder rungs are 16″: 15″ between the rails plus ½″ into a dado on each side.
Tag Part Length Qty Cut P Post half (glue two per post) 69″ 8 square R Long rail, back guard & back lower rail 76″ 5 square E End rail, end lower rail & end guard 48″ 8 square GA Front guard, head side of ladder 51″ 2 square GB Front guard, foot side of ladder 10″ 2 square L Ledger 76″ 2 square S Slat 39″ 14 square K Ladder rail 69″ 2 square U Ladder rung 16″ 4 square; ½″ dados in rails W Wall spacer block half (glue two per block) 5½″ 4 square Round every exposed corner and edge with sandpaper or a ¼″ roundover before assembly. Kids hit these with their heads. - 3
Posts and end frames
Glue and screw pairs of 69″ 2×4s face to face into four 3½″ × 3″ posts: 2½″ screws every 10″ in two staggered rows (3″ screws would come out the far side). The rails go on the 3″ sides and the long rails on a 3½″ face, so the long-rail bolts pass through both halves.
- Lay two posts on the floor 42″ apart (inside faces), glue lines facing up, and clamp a 48″ end rail across them, ends flush with the posts' outer edges, top edge 54″ from the post bottoms. Clamp a lower end rail the same way with its bottom edge 10″ up.
- Drill ⅜″ through rail and post: two 6″ carriage bolts at each end of the top rail, 1¼″ and 3⅜″ down from its top edge (the long-rail bolts pass between and below them later); one at each end of the lower rail, 2″ down. Keep every hole ¾″ to one side of the glue line, in the middle of one 2×4, never on the seam, and drill square so the bit stays inside that 2×4.
- Build the second end frame on top of the first.
Check: diagonals equal on each end frame before you drill. - 4
Long rails and ledgers
On the bench, glue and screw a 2×4 ledger on edge to the inside face of each 76″ long rail, its top 1½″ below the rail top so the slats finish flush. 2½″ screws every 8″, staggered.
- Stand both end frames with a helper. Set each long rail between them, against the inside face of the posts, ends tight to the end rails, top at 54″.
- Two carriage bolts per end, heads on the inside: a 7″ bolt 2¼″ down from the rail top through ledger, rail and post, and a 5″ bolt 4½″ down, just under the ledger, through rail and post only.
- The back lower rail goes between the end frames on the inside of the back posts with its bottom edge 10″ up (top at 15½″), one 5″ bolt per end, 4″ down from its top so it misses the end-rail bolt.
Check: diagonals of the deck rectangle equal, posts plumb both ways. Snug every nut, then tighten again tomorrow. - 5
Slats and mattress
14 39″ slats across the ledgers, about 2⅛″ apart, the end ones tight to the end rails. Two 3″ screws per end down into the ledgers so no slat can shift or lift.
The mattress sits on the slats inside a 76 × 39″ pocket framed by the guard boards (next step): ½″ of play all round, no gap for a child to slip into.
Mattress 75 × 38″, 8″ or thinner. A thicker mattress puts the sleeper above the guard rail; a smaller one leaves a gap at the side. - 6
Guard rails all round
Two 2×6 guard boards on every side, with 2″ gaps: the first starts 2″ above the deck, the second tops out at 69″, flush with the posts. That puts the guard top 7″ above an 8″ mattress.
- Back: 76″ boards on the inside face of the back posts, directly above the long rail, two 3″ screws into each post.
- Ends: 48″ boards on the outside face of the posts like the end rails. Kids brace their feet on these, so bolt them: one 6″ carriage bolt through the middle of the board into each post (off the glue line, as before), plus a 3″ screw into each post and one into the end of each long guard.
- Front: same plane as the front rail, leaving a 15″ opening for the ladder. Screw them to the posts now; the ends at the opening get screwed to the ladder rails next step.
Safety: guard top at least 5″ above the mattress on both long sides, even the wall side (kids slip into the gap between bed and wall). No opening in the guards larger than 3½″. - 7
Ladder
Cut ½″-deep dados across the inside face of both ladder rails at 10¾″, 21⅝″, 32⅜″, 43¼″ (rung tops). Set a circular saw to ½″ depth and nibble each 1½″ dado out, chisel flat.
- Glue the rungs into the dados and drive two 3″ screws through the rail into each rung end.
- Stand the ladder against the front long rail, its opening starting 51″ from the head end and lined up with the gap in the front guard. Bolt each ladder rail to the long rail with two carriage bolts: a 7″ bolt 2″ down from the rail top through ladder rail, long rail and ledger, and a 6″ bolt 4½″ down, under the ledger.
- Screw the front guard ends into the ladder rails from the inside.
The ladder rails run full height to the guard top so there's something to grab at the top. Never let a ladder rail stop at the deck. - 8
Anchor it to the wall
Push the bed tight to the wall; the back posts touch it and the top back guard sits 3″ off it. Find two wall studs behind that guard, ideally 32″ apart near the middle.
- Glue two 5½″ 2×4 offcuts face to face into a 3″-thick block. Make two.
- Slip a block between the guard and the wall at each stud, flush with the guard's top edge, and pin it with a 3″ screw through the guard.
- Pre-drill, then drive two 8″ structural screws at each block through guard and block into the stud. They should bite at least 2″ into the stud.
A tall bed with a kid climbing it rocks and racks. Anchoring to wall studs is required, not optional; drywall anchors don't count. Keep the bed at least 2′ from ceiling fans and away from windows and cords. - 9
Done
Twin loft bed, deck at 54″ with 48½″ clear underneath. Sand everything to 180, round every edge, and finish with low-VOC paint or water-based poly. Let it air out a few days before a kid sleeps in it.
Re-tighten all bolts after the first week and every few months after.
Upper deck is for kids 6 and up. One sleeper at a time, no jumping, and a night-light near the ladder.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
15 boards62% yield2×4 × 8′
19 boards81% yieldBuilt to the spirit of the U.S. bunk-bed safety standard (16 CFR 1513 / ASTM F1427): guard rails on all four sides, rail tops at least 5″ above the mattress, every opening in the guard 3½″ or less, a ladder opening no wider than 15″, and a mattress pocket only 1″ bigger than the mattress so there's no gap to slip into. Not for children under 6 on the upper deck.