Kayak Rack Builder
Shopping list
Pressure-treated 2×4s: the rack lives outside on the grass or gravel. Two A-frames, carriage-bolted, standing on shared skids and tied together with a ridge and a pair of cross braces so they can't rack.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 pressure-treated | 19 | $4.98 | $94.62 |
| ⅜″ × 5½″ galvanized carriage bolt with washer and nut (one per leg through each tie, collar and arm pair) | 16 | $1.20 | $19.20 |
| Galvanized angle bracket, 2×4 (ZMAX A35-style) (leg to skid) | 4 | $1.60 | $6.40 |
| #9 × 3″ exterior construction screws, 1-lb box | 1 | $11.00 | $11.00 |
| #9 × 2½″ exterior construction screws, 1-lb box | 1 | $11.00 | $11.00 |
| Outdoor carpet runner, 26″ × 6′ (8 pads, 8″ × 31⅜″) | 2 | $14.00 | $28.00 |
| Stainless staples, ½″, box | 1 | $6.00 | $6.00 |
| Total | $176.22 |
Tools: miter saw (set to 20°, then 37° for the cross braces) or circular saw and speed square, drill/driver, ¼″ and ⅜″ bits, socket wrench, staple gun, tape, clamps.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
19 boards83% yieldSized for boats up to about 75 lb each; the rack is not a ladder, so keep kids off the arms. Kayaks are carried hull-down on two supports about a third of the way in from each end; that's where the arms land. Paddleboards go deck-down (fins up and off). Prices are per board at the price you enter.
- 1
Shopping list
Pressure-treated 2×4s: the rack lives outside on the grass or gravel. Two A-frames, carriage-bolted, standing on shared skids and tied together with a ridge and a pair of cross braces so they can't rack.
Item Qty Each Total 2×4×8 pressure-treated 19 $4.98 $94.62 ⅜″ × 5½″ galvanized carriage bolt with washer and nut (one per leg through each tie, collar and arm pair) 16 $1.20 $19.20 Galvanized angle bracket, 2×4 (ZMAX A35-style) (leg to skid) 4 $1.60 $6.40 #9 × 3″ exterior construction screws, 1-lb box 1 $11.00 $11.00 #9 × 2½″ exterior construction screws, 1-lb box 1 $11.00 $11.00 Outdoor carpet runner, 26″ × 6′ (8 pads, 8″ × 31⅜″) 2 $14.00 $28.00 Stainless staples, ½″, box 1 $6.00 $6.00 Total $176.22 Tools: miter saw (set to 20°, then 37° for the cross braces) or circular saw and speed square, drill/driver, ¼″ and ⅜″ bits, socket wrench, staple gun, tape, clamps.
- 2
Cut list
Legs lean 20°, so both ends get a 20° cut, parallel to each other; measure the length along one edge. Arm crossbars get longer as you go down because the A spreads out. Cut the two cross braces last, after the frames are standing, and check them against the 74⅛″ listed.
Tag Part Length Qty Cut L Leg 56⅞″ 4 20° off square at both ends, cuts parallel (both ends sit level when the leg leans); length along either edge C Collar tie (pair at the apex, on edge) 10″ 4 square (trim to the leg line after) T Low tie (pair near the feet, on edge) 43″ 4 square (trim to the leg line after) A1 Arm crossbar, level 1 (on edge, pairs sandwich the legs) 92¾″ 4 square A2 Arm crossbar, level 2 (on edge, pairs sandwich the legs) 77½″ 4 square K Skid (flat, under both frames' legs) 88″ 2 45° chamfer on the ends R Ridge (flat, ties the two frames) 68½″ 1 square X Cross brace (on edge, between the frames) 74⅛″ 2 37° off square both ends, parallel (plumb when installed); length is long point to long point The listed crossbar lengths already include 30″ of reach past each leg. Collar and low-tie lengths reach the outside of the legs; trim the ends to the leg line after bolting if you like. - 3
Assemble the A-frames
Lay two legs on a flat floor in an A, the inside corners of the top cuts touching, the top cuts in one straight line and each leg leaning 20° off plumb. Clamp a collar tie across the top on each face so the pair sandwiches the legs, top edges flush with the top cuts.
Clamp a low-tie pair the same way with its top edge 8½″ up from a straightedge laid across the two foot cuts, measured square to it (10″ off the ground once the frame is on its skids).
- Drill ⅜″ through tie–leg–tie at each leg and bolt it. Snug, not crushed.
- Build the second frame on top of the first so they match exactly.
Check: measure the foot spread on both frames before you drill; they should both read 46⅜″ outside to outside at the foot cuts. - 4
Bolt on the arms
Each level is a pair of 2×4s on edge, one on each face of the frame, sandwiching both legs and sticking out 30″ past them on each side.
- Level 1: crossbars 92¾″ long, top edges 22½″ up from the foot line (24″ off the ground once the frame is on its skids), centered so the same amount sticks out each side.
- Level 2: crossbars 77½″ long, top edges 43½″ up from the foot line (45″ off the ground once the frame is on its skids), centered so the same amount sticks out each side.
Set each pair parallel to the foot line before you drill, then one ⅜″ carriage bolt through arm–leg–arm at each leg. Add two 2½″ screws per joint from each face to stop it pivoting on the bolt.
- 5
Skids, ridge and cross braces
- Lay the two 88″ skids flat and parallel, 39″ apart between their inside edges. Stand both frames on them 64″ apart on center, square to the skids, each foot's inside edge flush with the skid's inside edge and the skids running 12″ past each frame.
- Fix each leg to its skid with an angle bracket on the leg's wide face (it stays plumb) and two 3″ screws angled down through the leg into the skid.
- Lay the ridge flat across both apexes, ends flush with the outer collar ties, and drive two 3″ screws down into each collar tie. Plumb both frames before the last screws go in.
- Cross braces (74⅛″, ends cut parallel): stand each one on edge in the middle of the rack, side by side, one running from the low tie of the first frame up to the collar of the second, the other the opposite way. Each end bears on the face of a tie or collar; toe-screw them with 3″ screws.
On soft ground, set the skids on patio pavers so the rack doesn't sink unevenly. - 6
Pad the arms
Cut 8 strips of outdoor carpet 8″ wide and 31⅜″ long.
One strip covers each arm pair from the leg out to the tip (2 per frame per level): lay it across both top edges, fold it down the two outside faces and staple it there, below where the hull rubs.
- Split pool noodles zip-tied on work too and are cheaper.
- Keep staples off the top edges.
- 7
Done
Room for 4 kayaks. Kayaks go hull-down, cockpit up with a cover on, so rain doesn't collect.
Load both sides evenly, heaviest boats on the bottom level. A cable lock through the frames and the boats' grab handles keeps them yours.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
19 boards83% yieldSized for boats up to about 75 lb each; the rack is not a ladder, so keep kids off the arms. Kayaks are carried hull-down on two supports about a third of the way in from each end; that's where the arms land. Paddleboards go deck-down (fins up and off). Prices are per board at the price you enter.