Folding Workbench Builder
Shopping list
The ledger and hinge strip go into at least 3 wall studs each with ⅜″ lag screws: 6″ lags through the doubled ledger, 4″ through the single strip. On masonry, use ⅜″ sleeve anchors instead and skip the stud finder.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ stud, untreated SPF | 5 | $3.50 | $17.50 |
| ¾″ plywood, 4×8 sheet (a 2×4′ project panel also works) | 1 | $52.00 | $52.00 |
| ⅜″ × 6″ hex lag screws + washers (ledger) | 3 | $1.45 | $4.35 |
| ⅜″ × 4″ hex lag screws + washers (hinge strip) | 3 | $0.95 | $2.85 |
| 3½″ heavy butt hinge (top + legs) | 4 | $6.50 | $26.00 |
| #9 × 2½″ construction screws, 1-lb box (ledger layers, top frame) | 1 | $10.00 | $10.00 |
| #8 × 1¼″ wood screws, small box (plywood top, hinges) | 1 | $6.00 | $6.00 |
| Wood glue, 8 oz | 1 | $5.00 | $5.00 |
| Hook-and-eye latch, 4″ (holds it folded up) | 2 | $3.50 | $7.00 |
| ¼″ × 5″ structural wood screws (washer head) (legs to stretcher) | 4 | $1.60 | $6.40 |
| 3″ barrel bolt (locks each leg down) | 2 | $4.50 | $9.00 |
| Total | $146.10 |
Tools: stud finder, 4′ level, drill/driver with ¼″ and ⅜″ bits (and a 5/16″ bit for chain eye bolts), socket set for lags, circular saw, clamps, speed square.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
5 boards82% yieldSheet goods
- F Top: 1 × 48″ × 24″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
The top rests on a doubled 2×4 ledger lagged into the studs and pivots on hinges at a single 2×4 strip above it, so it folds up flat against the wall. All weight goes into the ledger and legs/chains, not the hinges. Prices are per board or sheet at the price you enter.
- 1
Shopping list
The ledger and hinge strip go into at least 3 wall studs each with ⅜″ lag screws: 6″ lags through the doubled ledger, 4″ through the single strip. On masonry, use ⅜″ sleeve anchors instead and skip the stud finder.
Item Qty Each Total 2×4×8′ stud, untreated SPF 5 $3.50 $17.50 ¾″ plywood, 4×8 sheet (a 2×4′ project panel also works) 1 $52.00 $52.00 ⅜″ × 6″ hex lag screws + washers (ledger) 3 $1.45 $4.35 ⅜″ × 4″ hex lag screws + washers (hinge strip) 3 $0.95 $2.85 3½″ heavy butt hinge (top + legs) 4 $6.50 $26.00 #9 × 2½″ construction screws, 1-lb box (ledger layers, top frame) 1 $10.00 $10.00 #8 × 1¼″ wood screws, small box (plywood top, hinges) 1 $6.00 $6.00 Wood glue, 8 oz 1 $5.00 $5.00 Hook-and-eye latch, 4″ (holds it folded up) 2 $3.50 $7.00 ¼″ × 5″ structural wood screws (washer head) (legs to stretcher) 4 $1.60 $6.40 3″ barrel bolt (locks each leg down) 2 $4.50 $9.00 Total $146.10 Tools: stud finder, 4′ level, drill/driver with ¼″ and ⅜″ bits (and a 5/16″ bit for chain eye bolts), socket set for lags, circular saw, clamps, speed square.
- 2
Cut list
Square cuts throughout. Cut the long pieces (both ledger layers, hinge strip, frame front and back) together so they come out identical.
Tag Part Length Qty Cut A Ledger (two layers) 48″ 2 square B Hinge strip 48″ 1 square C Top frame, front + back 48″ 2 square E Top frame, sides + middles 17″ 3 square F Top (24″ wide) 48″ 1 square L Leg 33¾″ 2 square S Leg stretcher 33″ 1 square The legs (33¾″) assume a flat floor. Cut them ¼″ long, hang the bench, then trim to level. - 3
Hang the ledger and hinge strip
Mark the studs. Snap a level line at 33¾″, the top of the ledger, and a second at 36″ for the bottom of the hinge strip; the 2¼″ between them is exactly the thickness of the top.
- Ledger: glue and screw the two ledger 2×4s face to face (2½″ screws every 12″, staggered) so it stands 3″ off the wall. The extra layer is what the top rests on; the single strip above stands only 1½″ off, so the top can pivot up past it.
- Hold the ledger to the lower line, pre-drill ¼″ pilots into each stud and drive a ⅜″ × 6″ lag with a washer through both layers. One per stud.
- Hinge strip (a single 2×4): bottom edge on the upper line, flush with the ledger ends, one ⅜″ × 4″ lag per stud.
- Check the ledger for level again after the lags are snug, before they're tight.
Lags must hit the center of the stud. Drywall anchors will not hold a workbench. - 4
Build the top frame
A flat 2×4 frame: front and back pieces run the full 48″, sides and 1 middle piece (17″) fit between, ends 3½″ apart from the others evenly spaced. Glue each joint and pin it with a 2½″ screw toed in at an angle (or a pocket screw); these only hold the frame together until the plywood goes on, and the glued plywood is what really ties it.
Square it by the diagonals, then set it on the ledger to check the fit: the back rail sits on the front layer of the ledger, and its back edge lines up with the face of the hinge strip, not tucked under it.
- 5
Skin the top
Glue and screw the 48″ × 24″ plywood to the frame, flush all round, 1¼″ screws every 8″, countersunk. The plywood squares the frame.
A sacrificial ¼″ hardboard layer on top, held with a few brads, lets you replace the work surface in ten minutes. - 6
Hinge it
Set the top on the ledger with its back edge flush with the face of the hinge strip. Mount 2 heavy 3½″ butt hinges in the corner between the strip face and the top surface, one leaf on each, knuckle right at the corner, about 6″ in from each end. Keep them clear of the lag heads.
Lift the front: it should rotate up and lie flat against the hinge strip. If it binds, the back edge is under the strip and catching on the ledger as it lifts; slide the top forward until it's flush.
- 7
Fold-down leg frame
Build an H frame: two legs (33¾″) with a 33″ stretcher between them, faces flush, its bottom 8″ off the floor. Glue the joints and drive two ¼″ × 5″ structural screws through the edge of each leg into the stretcher end (an ordinary 3″ screw won't reach through the 3½″ leg).
Hinge the leg tops to the underside of the front frame rail, 4″ in from each end, with the face of each leg ¼″ back from the front edge. Put the hinge knuckle on the back edge of the leg top, one leaf on the back face of the leg and one on the underside of the rail, so the leg folds back toward the wall and stops dead against the rail when it's vertical.
The legs are longer than the top is deep, so they can't fold flat while the top is down. That's fine: as you lift the top they swing back and hang, and once the top is up they lie flat against its underside.
Lock the legs: screw a 3″ barrel bolt to the inside edge of each leg at the top, and drill a matching hole up into the underside of the front rail. Shoot both bolts whenever the bench is down, so a kick or a sideways shove can't fold the legs under a loaded top.
With the legs down, the bench should not rack side to side. If it does, add a diagonal brace from a leg to the stretcher. - 8
Done
A 48″ × 24″ bench at 36″ that folds to about 5¼″ off the wall. To fold: pull both barrel bolts and lift the front; the leg frame swings back and hangs as the top rises, and lies flat against the underside once the top is up against the hinge strip. Screw the hook to the top's front edge and the eye into a stud above it, and hook it every time.
Always latch it when folded. A falling bench top is heavy enough to break a foot.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
5 boards82% yieldSheet goods
- F Top: 1 × 48″ × 24″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
The top rests on a doubled 2×4 ledger lagged into the studs and pivots on hinges at a single 2×4 strip above it, so it folds up flat against the wall. All weight goes into the ledger and legs/chains, not the hinges. Prices are per board or sheet at the price you enter.