Dog Bed & Ramp Builder
Shopping list
A L cushion (36×27″) drops into the frame with a little play. Untreated SPF is fine indoors; pick straight, dry studs so the frame doesn't twist after it's built.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ stud, untreated SPF | 6 | $3.50 | $21.00 |
| ¾″ plywood, 4×8 sheet (a 4×4 half sheet works if your store sells them) | 1 | $52.00 | $52.00 |
| #8 × 2½″ wood screws, 1-lb box (frame and ramp) | 1 | $10.00 | $10.00 |
| #8 × 3″ wood screws, small box (bumpers) | 1 | $6.00 | $6.00 |
| #8 × 1⅝″ wood screws, small box (decks and cleats) | 1 | $6.00 | $6.00 |
| Wood glue, 8 oz | 1 | $5.00 | $5.00 |
| Water-based polyurethane, 1 qt (pet-safe once cured) | 1 | $18.00 | $18.00 |
| 1×2×8 furring strip (ramp cleats) | 3 | $2.20 | $6.60 |
| Carpet runner or rubber stair tread, cut to fit (18″ × 5′ 8⅛″) | 1 | $15.00 | $15.00 |
| Heavy-duty staples, ⅜″ (T50), for the runner | 1 | $5.00 | $5.00 |
| Stick-on rubber feet, ¼″ thick, 4-pack (under the bed legs) | 1 | $5.00 | $5.00 |
| Dog bed cushion, L (36×27″) (if you don't have one; not counted) | 0 | $45.00 | $0.00 |
| Total | $149.60 |
Tools: miter or circular saw, drill/driver, countersink bit, tape, speed square, clamps, sander with 120-grit. A jigsaw if you cut the plywood yourself.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
6 boards87% yield1×2 × 8′
3 boards61% yieldSheet goods
- P Deck: 1 × 40″ × 29½″
- Q Ramp deck: 1 × 68⅛″ × 18″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
The frame is sized to standard rectangular dog-bed cushions with ½″ of play all round. Ramp slope is fixed at 20°, about the steepest older dogs and short-legged breeds handle comfortably. Prices are per board at the price you enter.
- 1
Shopping list
A L cushion (36×27″) drops into the frame with a little play. Untreated SPF is fine indoors; pick straight, dry studs so the frame doesn't twist after it's built.
Item Qty Each Total 2×4×8′ stud, untreated SPF 6 $3.50 $21.00 ¾″ plywood, 4×8 sheet (a 4×4 half sheet works if your store sells them) 1 $52.00 $52.00 #8 × 2½″ wood screws, 1-lb box (frame and ramp) 1 $10.00 $10.00 #8 × 3″ wood screws, small box (bumpers) 1 $6.00 $6.00 #8 × 1⅝″ wood screws, small box (decks and cleats) 1 $6.00 $6.00 Wood glue, 8 oz 1 $5.00 $5.00 Water-based polyurethane, 1 qt (pet-safe once cured) 1 $18.00 $18.00 1×2×8 furring strip (ramp cleats) 3 $2.20 $6.60 Carpet runner or rubber stair tread, cut to fit (18″ × 5′ 8⅛″) 1 $15.00 $15.00 Heavy-duty staples, ⅜″ (T50), for the runner 1 $5.00 $5.00 Stick-on rubber feet, ¼″ thick, 4-pack (under the bed legs) 1 $5.00 $5.00 Dog bed cushion, L (36×27″) (if you don't have one; not counted) 0 $45.00 $0.00 Total $149.60 Tools: miter or circular saw, drill/driver, countersink bit, tape, speed square, clamps, sander with 120-grit. A jigsaw if you cut the plywood yourself.
- 2
Cut list
Frame parts are all square cuts. The two ramp stringers are cut 68⅛″ along the top edge, with a 20° plumb cut at the top (miter saw at 20°) and a level cut at the foot: mark a line from the top-edge tip running 20° off the edge until it meets the bottom edge, 10¼″ long, and cut it with a jigsaw or circular saw so the whole cut lies flat on the floor. Leave the tip about ¼″ thick instead of a feather edge.
Tag Part Length Qty Cut A Long rail (front/back) 40″ 2 square B End rail 26½″ 2 square S Center stretcher 26½″ 1 square C Leg 8″ 4 square E Back bumper 40″ 1 square F End bumper 28″ 2 square P Deck (29½″ wide) 40″ 1 square R Ramp stringer 68⅛″ 2 20° plumb top; level-cut foot 10¼″ long H Ramp header (between stringers) 15″ 1 square J Ramp leg spreader 18″ 1 square K Ramp leg 22″ 2 square Q Ramp deck (18″ wide) 68⅛″ 1 square T Traction cleat 16″ 11 square Measure the real height of your couch cushion or mattress top before cutting the ramp. These lengths put the top of the ramp deck at exactly 24″; if yours differs by more than an inch, pick the closer ramp option or the dog has a step at the top. - 3
Build the base frame
Stand the two long rails (A) on edge and set the end rails (B) between them so the outside measures 40″ × 29½″.
- Glue the joints, drill pilot holes, and drive two 2½″ screws through each long rail into the end grain of each end rail.
- Add the center stretcher (S) halfway along, the same way, so the deck can't bounce.
- Measure both diagonals. Rack the frame until they match, then let the glue set.
- 4
Add the legs
Set a 8″ leg (C) inside each corner, wide face against the long rail and one edge tight to the end rail. The top of the leg sits flush with the top of the rails; the rails end up 4¾″ off the floor once the ¼″ rubber feet go on.
Clamp, then glue and two 2½″ screws through the long rail into the leg's face, plus two through the end rail into its edge, one above the other. Flip it over and check that all four legs touch on a flat floor.
- 5
Deck it
Lay the plywood deck (40″ × 29½″) over the frame, best face up. Line up the edges with the frame on two sides; the frame is now square because the plywood is.
- Glue the tops of the rails first.
- 1⅝″ screws every 6″ along the centerline of every rail and the stretcher, heads countersunk flush (the bumpers cover the back and end rows).
- Drill a few ½″ holes through the deck if your dog sleeps hot or the cushion gets damp.
- 6
Bumper rails and feet
The back bumper (E) runs the full 40″ on edge along the back of the deck, right over the back rail. The two end bumpers (F) butt into it and run to the front edge over the end rails. The front stays open so the dog steps straight in.
- Glue the bottoms, set them flush with the outside of the frame, and drive two 2½″ screws through the back bumper into the end of each end bumper.
- Clamp the bumpers down, flip the bed over, and fasten them from inside the frame: 3″ screws driven up at a steep angle (about 20° off vertical, leaning outward) through the inside face of the rail ¾″ below the deck, through the deck and into the bumper. One every 8″.
- While it's upside down, stick a ¼″ rubber foot under each leg.
Ease every edge and corner with 120-grit before finishing. Then one or two coats of water-based poly; let it cure a full week before the dog moves in. - 7
Ramp stringers and legs
The ramp is two stringers (R) on edge, 18″ apart outside to outside, their level-cut feet flat on the floor and their plumb-cut tops against the couch. Two legs (K) on the outside of the stringers carry the top end.
- Screw the header (H) between the stringers at the top, its back face flush with the plumb cuts and its top edge just under the stringers' top edges: two 2½″ screws through each stringer into its ends.
- Glue and screw a 22″ leg to the outside face of each stringer, back edge flush with the plumb cut and top flush with the stringer's top edge at its front corner: four 2½″ screws per leg.
- Screw the spreader (J) between the legs, back face flush, 3″ off the floor.
- Stand it against the couch or bed. The legs and the plumb cuts should sit flat against it and the feet flat on the floor; if it rocks, plane the long leg.
- 8
Ramp deck and cleats
Glue and screw the ramp deck (18″ × 68⅛″) to the stringers and header, 1⅝″ screws every 8″. Its bottom end sits on the floor at the stringer tips; bevel that edge with a sander so there's no lip, and its top end lands at 24″, flush with the couch.
Wrap a carpet runner or rubber tread over the deck and staple it underneath. Then screw the 11 traction cleats across the ramp every 6″, starting 4″ from the bottom, through the carpet, two 1⅝″ screws each.
Teach the ramp with treats on the cleats, going up first, before you ask the dog to come down it. - 9
Done
A 9″ raised bed for a L cushion (50–80 lb), plus a 5′ 8⅛″ ramp up to 24″. The deck keeps the cushion off a cold floor and out of drafts.
Every few months, check the ramp screws and the carpet staples. Loose carpet is the most common way dogs slip on a ramp.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
6 boards87% yield1×2 × 8′
3 boards61% yieldSheet goods
- P Deck: 1 × 40″ × 29½″
- Q Ramp deck: 1 × 68⅛″ × 18″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
The frame is sized to standard rectangular dog-bed cushions with ½″ of play all round. Ramp slope is fixed at 20°, about the steepest older dogs and short-legged breeds handle comfortably. Prices are per board at the price you enter.