Outdoor Dining Table Builder
Shopping list
Look for KDAT (kiln-dried after treatment) pressure-treated lumber: it's already dry, so it won't shrink, cup and open the gaps after you build. Sight down every 2×6 for the top and leave the twisted ones.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×6×8 pressure-treated (KDAT) (top) | 7 | $7.98 | $55.86 |
| 4×4×8 pressure-treated (legs) | 2 | $11.98 | $23.96 |
| 2×4×8 pressure-treated (KDAT) | 4 | $4.98 | $19.92 |
| ⅜″ × 6″ galvanized carriage bolt, washer, nut (aprons to legs (5″ of wood)) | 16 | $1.58 | $25.28 |
| Structural screw, 5″ (GRK/Spax type) (stretchers) | 12 | $1.10 | $13.20 |
| Exterior screws, 2½″, 1-lb box | 1 | $10.00 | $10.00 |
| Exterior penetrating stain/sealer, 1 qt | 1 | $22.98 | $22.98 |
| Sandpaper, 80 and 120 grit, pack | 1 | $9.98 | $9.98 |
| Total | $181.18 |
Tools: miter saw, drill/driver, ⅜″ bit at least 6″ long, socket wrench, random-orbit sander, speed square, 4′ level, clamps (four at least), tape, a ¼″ spacer (a carpenter's pencil works).
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
4×4 × 8′
2 boards60% yield2×6 × 8′
7 boards75% yield2×4 × 8′
4 boards84% yieldTop is 7 2×6s with ¼″ gaps so rain drains through: 40″ wide, 30″ tall, 6″ of overhang at the ends for chairs. Budget 24″ of table edge per person. Prices are per 8′ board at the price you enter.
- 1
Shopping list
Look for KDAT (kiln-dried after treatment) pressure-treated lumber: it's already dry, so it won't shrink, cup and open the gaps after you build. Sight down every 2×6 for the top and leave the twisted ones.
Item Qty Each Total 2×6×8 pressure-treated (KDAT) (top) 7 $7.98 $55.86 4×4×8 pressure-treated (legs) 2 $11.98 $23.96 2×4×8 pressure-treated (KDAT) 4 $4.98 $19.92 ⅜″ × 6″ galvanized carriage bolt, washer, nut (aprons to legs (5″ of wood)) 16 $1.58 $25.28 Structural screw, 5″ (GRK/Spax type) (stretchers) 12 $1.10 $13.20 Exterior screws, 2½″, 1-lb box 1 $10.00 $10.00 Exterior penetrating stain/sealer, 1 qt 1 $22.98 $22.98 Sandpaper, 80 and 120 grit, pack 1 $9.98 $9.98 Total $181.18 Tools: miter saw, drill/driver, ⅜″ bit at least 6″ long, socket wrench, random-orbit sander, speed square, 4′ level, clamps (four at least), tape, a ¼″ spacer (a carpenter's pencil works).
- 2
Cut list
Square cuts only (the cleat chamfers are cosmetic). Legs are 28½″: the top boards add 1½″ for a 30″ table. Cut all four legs from one stop block so it doesn't rock.
Tag Part Length Qty Cut T Top board, 2×6 72″ 7 square, ease the edges L Leg, 4×4 28½″ 4 square A Long apron (on edge) 60″ 2 square E End apron (on edge, between the long aprons) 33″ 2 square C Top cleat (flat, under the boards) 33″ 1 45° chamfer on the bottom corners S End stretcher (on edge, leg to leg) 26″ 2 square M Center stretcher (on edge) 52″ 1 square Pressure-treated sawdust: wear a mask, cut outside, and brush end-grain preservative on every fresh cut that ends up near the ground. - 3
End frames
Pick the four straightest faces of the 4×4s to face out.
Clamp an end apron across the outside of two legs, top edges flush with the leg tops and each end of the apron flush with a leg's outer face (legs 33″ apart outside to outside). Check square, drill ⅜″ through apron and leg, and bolt it with two bolts per leg on a diagonal: one 1″ down from the top, the other 2½″ down. Heads outside, washers and nuts inside.
Build both end frames on the floor with the leg tops against a straight board so they match exactly. - 4
Long aprons
Stand the end frames up 60″ apart outside to outside. Clamp the long aprons across the outside of the legs, covering the ends of the end aprons.
- Measure the diagonals across the top of the frame. Equal means square; rack it until they are, then bolt.
- Two bolts per leg here too, but side by side: both 1¾″ down from the top of the apron, 1¾″ apart and centered on the leg. At that height they pass between the two end-apron bolts inside the leg instead of hitting them.
- 5
H-stretcher
An end stretcher on edge between each pair of legs, 6″ off the floor and centered on the legs; then the center stretcher between them.
- Pre-drill and drive two 5″ structural screws through the leg into each end stretcher, and through each end stretcher into the center one.
- This is what stops the wobble when someone leans on a corner.
- 6
Top cleats
1 cleat laid flat between the long aprons, tops flush with the apron tops, evenly spaced. Two 2½″ screws through each apron into each cleat end.
The cleats tie every top board together from below, so no screw heads show on the top.
- 7
Top boards
Lay the 7 boards crown up with ¼″ gaps, 6″ past the frame at each end and 2″ at the sides. Start from the center board and work out.
- Screw up from below through the flat cleats: two 2½″ screws per board per cleat (1½″ cleat + 1½″ board, so they stop ½″ short of the top).
- The end aprons stand on edge, too tall to screw straight through: pre-drill and drive one 2½″ screw per board at a steep angle up through the inside face of each end apron (or use a pocket-hole jig).
- Sand the top with 80 then 120 grit and round every edge and corner; forearms rest here.
- 8
Done
A 6′ table that seats 6. Let KDAT lumber take a sealer right away; regular PT needs a month or two to dry first.
Glide pads or ½″ rubber feet under the legs keep the end grain out of puddles on a patio. Re-seal the top every spring.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
4×4 × 8′
2 boards60% yield2×6 × 8′
7 boards75% yield2×4 × 8′
4 boards84% yieldTop is 7 2×6s with ¼″ gaps so rain drains through: 40″ wide, 30″ tall, 6″ of overhang at the ends for chairs. Budget 24″ of table edge per person. Prices are per 8′ board at the price you enter.