Cornhole Board Builder
Shopping list
Regulation (ACA): 24×48 top, back edge 12″ high, front edge 4″, 6″ hole centered 9″ from the back edge. One sheet of plywood makes both tops with room to spare.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 stud, frames and legs | 5 | $3.50 | $17.50 |
| ½″ sanded plywood 4×8 (birch or BC; not OSB, bags won't slide) | 1 | $38.00 | $38.00 |
| ⅜″ × 4″ carriage bolt with 2 washers and a wing nut (leg pivot) | 4 | $2.98 | $11.92 |
| #8 × 1¼″ wood screws, top, small box (about 60) | 1 | $6.98 | $6.98 |
| #9 × 3″ wood screws, frame, small box (about 32) | 1 | $6.98 | $6.98 |
| Wood filler, 8 oz (for the screw heads) | 1 | $9.98 | $9.98 |
| Total | $91.36 |
Not in the total: primer, paint or stain, and a clear polyurethane topcoat, a quart each (~$30).
Tools: circular saw, jigsaw, drill with ⅜″ bit, countersink, 6″ hole saw or a jigsaw and a compass, sander, tape, square, bevel gauge.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
5 boards84% yieldSheet goods
- T Top, plywood: 2 × 48″ × 24″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Regulation (ACA): 24″ × 48″ top, back edge 12″ off the ground, front edge 4″ or less, 6″ hole centered 9″ from the back edge, boards 27′ apart front to front. Finish matters more than the frame: filled screw heads, sanded to 220, three coats of poly.
- 1
Shopping list
Regulation (ACA): 24×48 top, back edge 12″ high, front edge 4″, 6″ hole centered 9″ from the back edge. One sheet of plywood makes both tops with room to spare.
Item Qty Each Total 2×4×8 stud, frames and legs 5 $3.50 $17.50 ½″ sanded plywood 4×8 (birch or BC; not OSB, bags won't slide) 1 $38.00 $38.00 ⅜″ × 4″ carriage bolt with 2 washers and a wing nut (leg pivot) 4 $2.98 $11.92 #8 × 1¼″ wood screws, top, small box (about 60) 1 $6.98 $6.98 #9 × 3″ wood screws, frame, small box (about 32) 1 $6.98 $6.98 Wood filler, 8 oz (for the screw heads) 1 $9.98 $9.98 Total $91.36 Not in the total: primer, paint or stain, and a clear polyurethane topcoat, a quart each (~$30).
Tools: circular saw, jigsaw, drill with ⅜″ bit, countersink, 6″ hole saw or a jigsaw and a compass, sander, tape, square, bevel gauge.
- 2
Cut list
Quantities cover all 2 boards. Cut the plywood first with the factory edge on the long side; it's your straightest reference.
Tag Part Length Qty Cut T Top, plywood (24″ wide) 48″ 2 square R1 Side rail, 2×4 on edge 48″ 4 square R2 End rail and center support, 2×4 on edge 21″ 6 square L Leg, 2×4, 1¾″ radius on the top end 11⅜″ 4 radius top; foot mitered 9.7°: 11⅜″ on the back edge (long point), 10⅞″ on the front edge B Leg cross brace, 2×4 18″ 2 square The board slopes 9.7°. Each leg stands square to the deck, so its foot is mitered 9.7° to sit flat: the long point (11⅜″) is the edge that rests against the back rail, the short side (10⅞″) faces the front of the board. Cut one, test it, then use it as the pattern. - 3
Frame
Two side rails on edge, two end rails between them, plus a center support across the middle so the top doesn't drum when a bag lands.
- Two 3″ screws through the side rail into each rail end, pre-drilled.
- Check diagonals; square now or the top won't lie flat.
- 4
Top
Set the plywood on the frame, flush all round, best face up. Screw down every 6″ around the edge and along the center support, countersinking every head below the surface.
Fill the screw heads with wood filler and sand flush before paint; a bag catching on a screw head is the classic cornhole flaw. - 5
Hole
Mark the center 9″ in from the back edge, centered side to side. Cut the 6″ hole with a hole saw, or drill a starter hole and follow a compass line with the jigsaw.
- Sand the inside of the hole smooth and round the top edge slightly.
- Regulation: 6″ diameter, centered 9″ from the back edge and 12″ from each side.
- 6
Legs
Round the top end of each leg to a 1¾″ radius (trace a can lid) so it swings without hitting the top, and drill a ⅜″ hole at the radius center. Miter the foot 9.7°, long point on the edge that will face the back rail.
- Flip the board over. Set a leg inside each side rail with its back edge tight to the back rail. The bolt goes 3¼″ from the back of the board and 2¼″ below the top surface (about mid-rail). Drill through rail and leg together and fit the carriage bolt from the outside, washer, washer, wing nut inside.
- The back rail is the stop: swung out, the legs stand square to the deck. Fold them forward against the side rails for carrying.
- Screw the 18″ cross brace between the legs, 3″ up from the feet.
- Stand it up and check: back edge 12″ off the ground, front edge 4″.
- 7
Finish
Sand the top to 220. Prime, then paint or stain the top, two coats, and finish with two or three coats of polyurethane so the bags slide without being slick. Let it cure a few days before play.
- Leave the frame and legs plain or paint them a contrast color.
- Tape off stripes or a stencil between coats if you want a design.
- 8
Done
A set. Set the boards 27′ apart, front edge to front edge (regulation). Bags are 6×6, 1 lb each, four per side.
Store them face to face with a scrap between so the tops don't scuff, and keep them out of the rain: plywood swells, then the bags stop sliding.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
5 boards84% yieldSheet goods
- T Top, plywood: 2 × 48″ × 24″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Regulation (ACA): 24″ × 48″ top, back edge 12″ off the ground, front edge 4″ or less, 6″ hole centered 9″ from the back edge, boards 27′ apart front to front. Finish matters more than the frame: filled screw heads, sanded to 220, three coats of poly.