Chicken Coop Builder
Shopping list
Pressure-treated 2×4 for everything: the legs touch the ground and the rest lives in chicken dust and weather. Exterior-grade plywood only. The run is wrapped in ½″ hardware cloth; chicken wire keeps chickens in but not raccoons out.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 pressure-treated | 28 | $4.98 | $139.44 |
| 2×4×10 pressure-treated | 4 | $6.85 | $27.40 |
| ¾″ exterior plywood, 4×8 sheet (floor) | 1 | $52.00 | $52.00 |
| ½″ exterior plywood, 4×8 sheet (walls, roof, nest box, ramp) | 5 | $38.00 | $190.00 |
| 1×2×8 furring strip (ramp cleats) | 2 | $1.48 | $2.96 |
| Corrugated steel roof panel, 26″ × 8′ | 4 | $27.98 | $111.92 |
| Roofing screws with washers, 100-pack | 1 | $11.98 | $11.98 |
| Hurricane tie (rafter to plate) | 8 | $1.18 | $9.44 |
| #9 × 3″ exterior construction screws, 5-lb box | 1 | $38.00 | $38.00 |
| Exterior screws, 1⅝″, 1-lb box (plywood) | 2 | $10.00 | $20.00 |
| Strap hinge, 4″ (coop door, nest lid, run door) | 6 | $4.48 | $26.88 |
| Barrel bolt, 3″ (raccoons open hook latches) | 3 | $3.98 | $11.94 |
| ½″ hardware cloth, 36″ × 10′ (eave vents) | 1 | $27.98 | $27.98 |
| Exterior sealant, paintable, 10 oz tube (plywood corners and the nest-lid hinge line) | 1 | $7.98 | $7.98 |
| ½″ hardware cloth, 48″ × 25′ roll | 3 | $89.00 | $267.00 |
| Poultry staples, 1″, 1-lb | 1 | $7.98 | $7.98 |
| Total | $952.90 |
Tools: circular saw, jigsaw, drill/driver, speed square, 4′ level, tape, chalk line, clamps, staple gun or hammer, tin snips, sawhorses. A helper for the roof.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
28 boards90% yield2×4 × 10′
4 boards93% yield1×2 × 8′
2 boards50% yieldSheet goods
- P1 Floor, ¾″ plywood (notch each corner 5″ × 3″ for the posts): 1 × 72″ × 48″
- P2 Front wall, ½″ plywood (door cut out of it): 1 × 72″ × 47¾″
- P3 Back wall, ½″ plywood: 1 × 72″ × 35¾″
- P4 Side wall, ½″ plywood (taper the top): 2 × 48″ × 47¾″
- P5a Roof sheathing, ½″ plywood: 1 × 62″ × 48″
- P5b Roof sheathing, ½″ plywood: 1 × 62″ × 24″
- P6 Nest box bottom: 1 × 25½″ × 12″
- P7 Nest box front: 1 × 24½″ × 13½″
- P8 Nest box end: 2 × 12″ × 13½″
- P8b Nest box divider: 1 × 11½″ × 13½″
- P9 Nest box lid: 1 × 26½″ × 13″
- P10 Ramp: 1 × 44⅛″ × 12″
- P11 Pop door (slides up): 1 × 13″ × 13″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
The coop floor gets 4 ft² per hen; the run gets 10 ft² per hen, counting the shade under the coop. The roof sheds to the back, where the nest boxes hang, so eggs are collected from outside. Prices are per board at the price you enter.
- 1
Shopping list
Pressure-treated 2×4 for everything: the legs touch the ground and the rest lives in chicken dust and weather. Exterior-grade plywood only. The run is wrapped in ½″ hardware cloth; chicken wire keeps chickens in but not raccoons out.
Item Qty Each Total 2×4×8 pressure-treated 28 $4.98 $139.44 2×4×10 pressure-treated 4 $6.85 $27.40 ¾″ exterior plywood, 4×8 sheet (floor) 1 $52.00 $52.00 ½″ exterior plywood, 4×8 sheet (walls, roof, nest box, ramp) 5 $38.00 $190.00 1×2×8 furring strip (ramp cleats) 2 $1.48 $2.96 Corrugated steel roof panel, 26″ × 8′ 4 $27.98 $111.92 Roofing screws with washers, 100-pack 1 $11.98 $11.98 Hurricane tie (rafter to plate) 8 $1.18 $9.44 #9 × 3″ exterior construction screws, 5-lb box 1 $38.00 $38.00 Exterior screws, 1⅝″, 1-lb box (plywood) 2 $10.00 $20.00 Strap hinge, 4″ (coop door, nest lid, run door) 6 $4.48 $26.88 Barrel bolt, 3″ (raccoons open hook latches) 3 $3.98 $11.94 ½″ hardware cloth, 36″ × 10′ (eave vents) 1 $27.98 $27.98 Exterior sealant, paintable, 10 oz tube (plywood corners and the nest-lid hinge line) 1 $7.98 $7.98 ½″ hardware cloth, 48″ × 25′ roll 3 $89.00 $267.00 Poultry staples, 1″, 1-lb 1 $7.98 $7.98 Total $952.90 Tools: circular saw, jigsaw, drill/driver, speed square, 4′ level, tape, chalk line, clamps, staple gun or hammer, tin snips, sawhorses. A helper for the roof.
- 2
Cut list
Frame first, plywood after: cut the 2×4s from the list, but measure the built frame before you cut sheet goods. Wall heights: 43½″ at the front, 31½″ at the back, floor to plate top.
Tag Part Length Qty Cut A Front corner post (inside the corner, ground to plate top) 68¼″ 2 square B Back corner post (inside the corner, ground to plate top) 56¼″ 2 square C Floor rim, front & back (on edge, full length) 72″ 2 square D Floor rim, sides (on edge) 45″ 2 square E Floor joist, 16″ on center 45″ 4 square F Mid leg (inside the rim, ground to the underside of the floor) 24″ 2 square G Top plate, front & back (on edge, full length) 72″ 2 square H Front wall stud (flat): mid stud and door jamb 40″ 2 square I Back mid stud (flat) 28″ 1 square J End-wall stud (flat; carries the roost) 37¼″ 2 14° miter across the wide face on top, to match the rafter; length is to the short point K Rafter (on edge) 62″ 4 14° plumb cut both ends, parallel; no birdsmouth M Roost bar (flat, edges rounded) 69″ 1 square N Roost cleat 6″ 2 square O Nest box ledger and front rail 25½″ 2 square O2 Nest box leg (behind the front rail) 24″ 2 square R1 Run sill & top plate, sides (flat) 108″ 4 square R2 Run end sill (flat) 41″ 2 square R3 Run post & door jamb 45″ 10 square R4 Run top cross tie (flat) 41″ 4 square R5 Run diagonal brace 52⅝″ 2 level ends: 31° off square both ends, parallel; scribe in place R6 Run door stile 44½″ 2 square R7 Run door rail 16½″ 2 square R8 Run door brace 39⅝″ 1 level ends: 19° off square both ends, parallel; scribe in place P1 Floor, ¾″ plywood (notch each corner 5″ × 3″ for the posts) (48″ wide) 72″ 1 square P2 Front wall, ½″ plywood (door cut out of it) (47¾″ wide) 72″ 1 square P3 Back wall, ½″ plywood (35¾″ wide) 72″ 1 square P4 Side wall, ½″ plywood (taper the top) (47¾″ wide) 48″ 2 square P5a Roof sheathing, ½″ plywood (48″ wide) 62″ 1 square P5b Roof sheathing, ½″ plywood (24″ wide) 62″ 1 square P6 Nest box bottom (12″ wide) 25½″ 1 square P7 Nest box front (13½″ wide) 24½″ 1 square P8 Nest box end (13½″ wide) 12″ 2 square P8b Nest box divider (13½″ wide) 11½″ 1 square P9 Nest box lid (13″ wide) 26½″ 1 square P10 Ramp (12″ wide) 44⅛″ 1 square P11 Pop door (slides up) (13″ wide) 13″ 1 square Q Ramp cleat, 1×2 12″ 8 square Snap the side-wall taper on the plywood from 47¾″ at the front to 35¾″ at the back. Cut one, check it, and trace the second from it. - 3
Legs and floor frame
The corner posts run from the ground to the top plates, so the legs and the wall corners are one piece. Build the floor frame (rims and joists) flat on the ground first, then fasten it to the posts.
- Front and back rims run the full 72″ on edge; the side rims fit between them. Screw through the front and back rims into the side-rim ends (three 3″ screws per corner). Rim tops are 24″ off the ground.
- Mark every post 24″ up from its bottom end. Stand the frame on its back rim, lay the two long front posts inside the front corners (wide face against the rim, edge tight to the side rim, rim top on the mark) and screw them on: three 3″ screws through the rim into the post, two through the side rim into the post's edge. Roll the frame over and do the two shorter back posts the same way, then stand it up with a helper.
- 4 joists 16″ on center between the front and back rims, two screws per end.
- Two 24″ mid legs inside the front and back rims, tight against the joist nearest the middle, tops flush with the rim tops, three 3″ screws through the rim into each. They keep the long rims from sagging.
Set each leg on a patio paver, then level the frame both ways. Measure the diagonals: equal means square. - 4
Floor and wall framing
Notch the ¾″ plywood floor 5″ × 3″ at each corner so it drops around the posts, and screw it to the rims and joists every 8″.
- Top plates on edge, full length across the front and back, screwed into the post faces: front tops at 43½″ above the floor, back at 31½″. That 12″ drop is the roof slope.
- Wall studs go in flat, wide face to the outside, standing on the floor and toe-screwed top and bottom: one centered under each plate, plus a door jamb in the front wall, 22½″ clear of the mid stud (its far edge 8¼″ from the outside of the end wall). Put the jamb toward the end that will not get the pop door and ramp: that's the right-hand end as you face the front. The door closes against the jamb and the mid stud.
- A 37¼″ stud in the middle of each end wall, flat like the others, its top mitered to the roof slope and its outside face flush with the end of the floor. Toe-screw the bottom now; the top gets screwed to the end rafter in the next step. The roost hangs off these.
- 5
Rafters
4 rafters on edge, front plate to back plate, 6″ overhang at each end. Cut a 14° plumb cut on both ends so the fascia is vertical.
- The end rafters sit on the ends of the plates, flush with the end walls, and land on the mitered tops of the end-wall studs: toe-screw each stud up into its rafter.
- No birdsmouth needed: each rafter bears on the inside edge of the front plate and the outside edge of the back plate. A hurricane tie on each end of every rafter. Wind gets under a shed roof.
- 6
Plywood walls
Screw the front and back plywood on first, bottom edges flush with the bottom of the rims, then the tapered side panels. 1⅝″ screws every 6″ on the edges, 12″ in the field.
- Coop door: before hanging the front panel, draw a 24″ × 31½″ door on it, 11″ from the end of the panel on the jamb side and 8¼″ up from its bottom edge (4″ above the floor), so its sides overlap the jamb and the mid stud by ¾″. Drill a starter hole in a corner and cut it out with the jigsaw. The cutout is the door, and the studs behind it are its stops.
- Hang the door on two strap hinges screwed through the siding into the jamb, and fit a barrel bolt on the other side into the mid stud. Glue and screw a scrap of plywood behind each hinge and the bolt on the inside of the door so the screws have 1″ to bite.
- Run a bead of sealant down each corner where the side panels meet the front and back.
- Nest holes: the nest bank is 25½″ wide and starts 6⅝″ from the end of the coop without the pop door (the same end as the door jamb). Cut 2 holes, 10″ wide × 9″ tall, through the back panel, one centered on each 12″ box, bottom edge 3″ above the floor so the coop bedding stays out of the nests.
- Pop door: a 12″ × 12″ hole at floor level in the other end wall (the left-hand end as you face the front), its back edge 6″ from the back corner. The ramp and the run go on this end.
- 7
Roof
Screw the ½″ plywood to the rafters, then the 4 corrugated panels on top, overlapping one corrugation, 2″ past the sides and 1″ past the front and back.
- Roofing screws go through the top of the ridges, not the valleys, every 12″.
- Pre-drill the metal with a ⅛″ bit so the washers seat flat.
- 8
Nest box, roost and ramp
The nest bank hangs off the back wall: 2 boxes, 12″ wide, 12″ deep. Its bottom sits on a 2×4 ledger screwed through the siding into the back floor rim (it lines up exactly) and, at the outer edge, on a matching front rail carried by two 24″ legs set on pavers. Screw the bottom down to both, then build the ends, divider, front and lid on it with 1⅝″ screws into pilot holes. Hinge the lid along the wall so you can collect eggs from outside, bolt it shut, and seal the hinge line so rain can't run in.
- Roost bar flat, wide face up, 18″ above the floor on cleats screwed to the side studs. Round its edges with a sander; chickens perch flat-footed.
- Pop door: a 13″ square of plywood that slides up and down between two strips of scrap screwed beside the opening on the outside. Drill it for a pin or a cord so it stays up by day and locks down at night.
- Ramp: the 44⅛″ × 12″ strip at about 35°, with 8 1×2 cleats every 5″ (glue, and 1⅝″ screws up through the plywood). Rest the top on the sill of the pop-door opening and screw it to a scrap block fixed to the siding just below; the foot sits on the ground inside the run.
Roost higher than the nest boxes, always. Otherwise the hens sleep in the nests and foul the eggs. - 9
Vents and run
Staple ½″ hardware cloth across the open rafter bays front and back. That's your ventilation; a coop needs it even in winter.
- Run frame: 2×4 sills flat on the ground, posts every 34⅞″ on center, flat top plates and cross ties. Screw down through the plates and up through the sills into the post ends; toe-screw the end sills and cross ties. Butt the near end against the coop's side wall and toe-screw the near-end posts through the siding into the side floor rim.
- A diagonal brace in the far bay of each long side. In the far end, two jambs 24″ apart and a framed 2×4 door 23½″ × 44½″: rails between the stiles (two 3″ screws toed through each rail end), a brace rising from the bottom hinge corner, hardware cloth stapled over the outside. Hang it on strap hinges, flush with the outside, with a barrel bolt.
- Wrap the sides, end and top in hardware cloth with poultry staples every 4″. Skirt the three open sides under the coop (the hens use that shade as part of the run), and run a 12″ apron flat on the ground around the whole footprint so nothing digs in.
- 10
Done
Room for 6 hens: 24 ft² of coop and 36 ft² of run. Paint or stain all the plywood, especially the bottom edges.
Bedding: 3–4″ of pine shavings on the floor, straw in the nest boxes. A sheet of vinyl flooring under the shavings makes cleanout a 10-minute job.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
28 boards90% yield2×4 × 10′
4 boards93% yield1×2 × 8′
2 boards50% yieldSheet goods
- P1 Floor, ¾″ plywood (notch each corner 5″ × 3″ for the posts): 1 × 72″ × 48″
- P2 Front wall, ½″ plywood (door cut out of it): 1 × 72″ × 47¾″
- P3 Back wall, ½″ plywood: 1 × 72″ × 35¾″
- P4 Side wall, ½″ plywood (taper the top): 2 × 48″ × 47¾″
- P5a Roof sheathing, ½″ plywood: 1 × 62″ × 48″
- P5b Roof sheathing, ½″ plywood: 1 × 62″ × 24″
- P6 Nest box bottom: 1 × 25½″ × 12″
- P7 Nest box front: 1 × 24½″ × 13½″
- P8 Nest box end: 2 × 12″ × 13½″
- P8b Nest box divider: 1 × 11½″ × 13½″
- P9 Nest box lid: 1 × 26½″ × 13″
- P10 Ramp: 1 × 44⅛″ × 12″
- P11 Pop door (slides up): 1 × 13″ × 13″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
The coop floor gets 4 ft² per hen; the run gets 10 ft² per hen, counting the shade under the coop. The roof sheds to the back, where the nest boxes hang, so eggs are collected from outside. Prices are per board at the price you enter.