Adirondack Chair Builder
Shopping list
Pressure-treated 2×4 and 2×6 for the frame and arms. For the 1×6 slats, cedar fence boards or treated 1×6 if your store carries it; plain pine 1×6 needs a good exterior paint. Pick the clearest, flattest boards for the arms: everyone touches them.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ pressure-treated (legs, braces, apron) | 3 | $4.98 | $14.94 |
| 2×6×8′ pressure-treated (stringers, arms) | 4 | $7.98 | $31.92 |
| 1×6×6′ board (cedar or treated) (back and seat slats) | 8 | $5.44 | $43.52 |
| ⅜″ × 4″ galvanized carriage bolt, nut + washer (legs to stringers) | 8 | $1.48 | $11.84 |
| #9 × 3″ exterior screws, 1-lb box (frame and arms) | 1 | $10.98 | $10.98 |
| #8 × 2″ exterior screws, 1-lb box (1× slats) | 1 | $9.98 | $9.98 |
| Exterior wood glue, 8 oz | 1 | $5.98 | $5.98 |
| Total | $129.16 |
Tools: miter saw, drill/driver, countersink bit, ⅜″ bit and socket wrench, 2 bar clamps, speed square or bevel gauge, sander. A helper for the back.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
4 boards76% yield2×4 × 8′
3 boards89% yield1×6 × 6′
8 boards80% yieldSeat slopes back 15°, back reclines 27° from vertical, for a 102° seat-to-back angle. Every cut is straight: one 12° crosscut on the back-slat bottoms and one 27° bevel rip on the upper brace; the rest are square. Prices are per 8′ board at the price you enter (6′ 1×6 boards are priced pro rata).
- 1
Shopping list
Pressure-treated 2×4 and 2×6 for the frame and arms. For the 1×6 slats, cedar fence boards or treated 1×6 if your store carries it; plain pine 1×6 needs a good exterior paint. Pick the clearest, flattest boards for the arms: everyone touches them.
Item Qty Each Total 2×4×8′ pressure-treated (legs, braces, apron) 3 $4.98 $14.94 2×6×8′ pressure-treated (stringers, arms) 4 $7.98 $31.92 1×6×6′ board (cedar or treated) (back and seat slats) 8 $5.44 $43.52 ⅜″ × 4″ galvanized carriage bolt, nut + washer (legs to stringers) 8 $1.48 $11.84 #9 × 3″ exterior screws, 1-lb box (frame and arms) 1 $10.98 $10.98 #8 × 2″ exterior screws, 1-lb box (1× slats) 1 $9.98 $9.98 Exterior wood glue, 8 oz 1 $5.98 $5.98 Total $129.16 Tools: miter saw, drill/driver, countersink bit, ⅜″ bit and socket wrench, 2 bar clamps, speed square or bevel gauge, sander. A helper for the back.
- 2
Cut list
Stringers 36″, arms 36⅞″. Two angled cuts: the bottom end of every back slat is cut 12° off square, so it sits flat on the 15° stringer while the slat leans 27°; and the upper brace gets its top edge ripped at a 27° bevel, so the level arms sit flat on it. The two middle back slats are 3″ longer than the outer two, so the top steps up in the middle; round the tops with a jigsaw if you want the classic curve.
Tag Part Length Qty Cut S Stringer, 2×6 36″ 4 square; round the front top corner L Front leg, 2×4 21″ 4 square F Front apron, 2×4 27″ 2 square B Lower back brace, 2×4 24″ 2 square U Upper back brace (arm support), 2×4 35″ 2 square; top edge ripped at a 27° bevel A Arm, 2×6 on the flat 36⅞″ 4 round the front corners T Seat slat, 1×6 24″ 8 square K Back slat, outer, 1×6 32″ 4 bottom 12° off square, long point on the front face K Back slat, middle, 1×6 35″ 4 bottom 12° off square, long point on the front face - 3
Stringers and front legs
Clamp a 21″ leg to the outside of each stringer. The stringer slopes down 15° to the back, its back-bottom corner on the floor; the leg stands plumb with its front edge flush with the stringer's front-bottom corner, which sits 9⅜″ off the floor and 34¾″ in front of the back corner.
- Set it up on a flat floor with a speed square on the leg and a bevel gauge at 15° on the stringer.
- Drill two ⅜″ holes through leg and stringer: one 10½″ off the floor and 1¾″ back from the leg's front edge, one 13″ off the floor and 2½″ back. Staggered like that, both stay well clear of the stringer's end and edges. Carriage bolts in from the outside, washer and nut inside.
- Make the second side as a mirror image: legs on the outside of both.
- 4
Front apron
Stand the two sides up 21″ apart inside, legs outside. Screw the 27″ apron across the front edges of both legs, 9½″ off the floor, with two 3″ screws into each leg; its ends are flush with the outside of the legs.
- Clamp a scrap across the backs of the stringers to hold them 21″ apart until the seat slats are on.
- Check the base is square by its diagonals and that both stringers touch the floor at the back.
- 5
Seat slats
4 1×6 slats across the top edges of the stringers, ⅜″ apart, ends flush with the outside of the stringers. Start with the front one flush with the stringer fronts and work back; the last one ends 23⅛″ back from the stringer fronts.
- Two 2″ screws into each stringer, pilot-drilled and countersunk.
- Sand a generous round on the front edge of the front slat. It's under your knees.
- 6
Back panel
4 back slats, middle two long, outer two short, leaning back 27° from plumb. Stand them with their 12° bottom ends tight behind the last seat slat: the outer two sit flat on the stringer tops, the middle two line up with them. Space them ⅝″ apart, outer edges flush with the outside of the stringers.
- Have a helper hold the slats at 27° (bevel gauge against the front face), or tack a temporary strip across their tops to a stick clamped to the stringers.
- Slide the 24″ lower brace down behind the slats until its back edge sits on the stringer tops. Glue, then two 2″ screws through each slat into it, then two 3″ screws toed through the brace into each stringer.
- 7
Upper brace and arms
Rip a 27° bevel along the top edge of the 35″ upper brace: the back face stays the full 3½″ and the front face, the one that goes against the slats, comes out about 2¾″ wide. Hold it behind the back slats, centered side to side, with its beveled top level and 21″ off the floor (the same height as the leg tops), and glue and screw through each back slat into it with two 2″ screws. It sticks out 5½″ past the back panel on each side; that is what the arms land on.
- Arms lie flat on the front legs and the ends of the upper brace, overhanging the leg 3″ in front and 4″ to the outside; the inside edge lines up with the outside of the stringer and the outer back slat.
- Two 3″ screws down into each leg top, two into the brace. Check the arms are level and parallel before driving them.
Optional: a small 2×4 corbel under the front of each arm, screwed to the outside of the leg, stiffens it for people who push up on the arms to stand. - 8
Done
2 chairs: seat front 15⅜″ off the ground, back reclined 27°, arms at 22½″ and wide enough for a drink.
Break every edge with sandpaper, then paint or stain. End grain on the leg bottoms and stringer backs drinks water; seal it twice.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
4 boards76% yield2×4 × 8′
3 boards89% yield1×6 × 6′
8 boards80% yieldSeat slopes back 15°, back reclines 27° from vertical, for a 102° seat-to-back angle. Every cut is straight: one 12° crosscut on the back-slat bottoms and one 27° bevel rip on the upper brace; the rest are square. Prices are per 8′ board at the price you enter (6′ 1×6 boards are priced pro rata).